Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 30

30

Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON,

S5232F-ON and S5148F-ON

S5148F-Leaf1A

S5148F-Leaf1B

switchport trunk allowed vlan 1612-

1615

spanning-tree port type edge

flowcontrol receive on

flowcontrol transmit off

no shutdown

interface ethernet1/1/18

description Node2_Port1

switchport mode trunk

switchport access vlan 1611


1615




no shutdown






1615




no shutdown






1615




no shutdown


1615




no shutdown






1615




no shutdown






1615




no shutdown






1615




no shutdown

7.2.4

Configure the switch interconnect

Create a port channel to use between the two leaf switches, 127 in this example. Use the

switchport

mode trunk

command to enable the port channel to carry traffic for multiple VLANs, and allow all VLANs on

the port channel.

Use 100GbE interfaces for the port channel, 1/1/53 and 1/1/54 in this example. Add each interface to the port

channel as LACP active members with the

channel-group 127 mode active

command.

When the configuration is complete, exit configuration mode and save the configuration with the

end

and

write memory

commands.

Section	Page
1 Introduction	6
1.1 Supported switches and operating systems	7
1.2 Typographical conventions	8
1.3 Attachments	8
2 Hardware overview	9
2.1 Dell EMC Networking S5248F-ON	9
2.2 Dell EMC Networking S5232F-ON	9
2.3 Dell EMC Networking S5148F-ON	9
2.4 Dell EMC Networking S3048-ON	9
2.5 Dell EMC VxRail 14G nodes	10
2.5.1 Dell EMC VxRail P Series node	10
2.5.2 Dell EMC VxRail V Series node	10
2.5.3 Dell EMC VxRail S Series node	10
2.5.4 Dell EMC VxRail E Series node	10
2.5.5 VxRail node network adapters	10
3 Topology options	12
3.1 Dual switch	12
3.1.1 Dual switch with VLT	12
3.1.2 Dual switch without VLT	13
3.2 Single switch	14
4 VxRail in the data center	15
4.1 Leaf-spine network	15
4.2 OOB management network	16
5 Configuration planning	17
5.1 VLANs and IP addresses	17
5.2 VxRail network configuration table	18
5.3 Using a jump box or laptop computer	19
5.4 DNS and NTP servers	19
6 Switch configuration prerequisites	21
6.1 Check switch OS version	21
6.2 Verify license installation	21
6.3 Factory default configuration	22
7 Configure switches	23
7.1 Dual switch with VLT	23
7.1.1 General settings	23
7.1.2 Configure VLANs	24
7.1.3 Configure interfaces	25
7.1.4 Configure VLT	26
7.2 Dual switch without VLT	27
7.2.1 General settings	28
7.2.2 Configure VLANs	28
7.2.3 Configure interfaces	29
7.2.4 Configure the switch interconnect	30
7.3 Single switch	31
7.3.1 General settings	32
7.3.2 Configure VLANs	32
7.3.3 Configure interfaces	33
8 Switch validation	36
8.1 General validation commands	36
8.1.1 show interface status	36
8.1.2 show port-channel summary	36
8.1.3 show vlan	37
8.1.4 show lldp neighbors	38
8.1.5 show vrrp brief	39
8.2 VLT validation commands	39
8.2.1 show vlt domain_id	39
8.2.2 show vlt domain_id backup-link	39
8.2.3 show vlt domain_id mismatch	40
9 Deploy VxRail	41
10 Use of VxRail 4.7.0 to validate Dell EMC Networking S5200F-ON	43
A Validated components for S5148F-ON using VxRail 4.5	45
A.1 Dell EMC Networking Switches	45
A.2 DAC Cables	45
A.3 VxRail P570 nodes	45
A.4 VxRail Appliance software	46
B Validated components for S5248F-ON and S5232F-ON using VxRail 4.7.0	47
B.1 Dell EMC Networking switches	47
B.2 DAC Cables	47
B.3 VxRail E560 nodes	47
B.4 VxRail appliance software	48
C VxRail network adapter traffic optimization	49
D Configure breakouts on port groups and interfaces	50
D.1 Breakout port-groups for S5248F-ON	50
D.2 Breakout interfaces for S5232F-ON	51
D.3 Auto-breakout feature	51
E Technical resources	52

Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 30

Con the switch interconnect

Page 30 highlights