Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 43

43

Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON,

S5232F-ON and S5148F-ON

10

Use of VxRail 4.7.0 to validate Dell EMC Networking

S5200F-ON

With VxRail 4.7.0, two in-band management networks are used - public and private. In this example, VLAN

3939 serves as the default VLAN for the VxRail private management network, and VLAN 1611 remains as the

public in-band management network. The Node discovery network is isolated to VLAN 3939. The Leaf

switches must be configured appropriately for the changes to be incorporated.

S5248F-Leaf1

S5248F-Leaf2

VLTi

17

17

VxRail node

S5248F-Leaf1

S5248F-Leaf2

VLTi

17

17

VxRail node

Management traffic split into

public and private network

VxRail 4.7

Prior to VxRail 4.7

Switches configured for

management

traffic

, vSAN traffic, vMotion, and VM

networks.

Switches configured for

public management

traffic, private management traffic

, vSAN

traffic, vMotion, and VM networks.

25GbE connection.

25GbE connection.

VxRail 4.7 deployment with Dell EMC Networking S5200F-ON switches

In addition to the configuration provided in the prior examples for the S5148F-ON in

Chapter 7

, the leaf

switches require the listed command configuration to validate the S5200F-ON with VxRail 4.7.0. The

configuration includes creation of VLAN 3939 and enables the VLAN to access the necessary trunk ports as

dictated by the topology. For example, in a topology of leaf switches in VLT, the additional configuration with

VLAN 3939 on the leaf switches is shown below.

Additional VLAN configuration on leaf switches

S5248F-Leaf1A

S5248F-Leaf1B

interface vlan3939

description default-private-vlan

no shutdown

interface ethernet1/1/17

switchport trunk allowed vlan 1612-

1615,3939



1615,3939



1615,3939



1615,3939

interface vlan3939

description default-private-vlan

no shutdown



1615,3939



1615,3939



1615,3939



1615,3939

Section	Page
1 Introduction	6
1.1 Supported switches and operating systems	7
1.2 Typographical conventions	8
1.3 Attachments	8
2 Hardware overview	9
2.1 Dell EMC Networking S5248F-ON	9
2.2 Dell EMC Networking S5232F-ON	9
2.3 Dell EMC Networking S5148F-ON	9
2.4 Dell EMC Networking S3048-ON	9
2.5 Dell EMC VxRail 14G nodes	10
2.5.1 Dell EMC VxRail P Series node	10
2.5.2 Dell EMC VxRail V Series node	10
2.5.3 Dell EMC VxRail S Series node	10
2.5.4 Dell EMC VxRail E Series node	10
2.5.5 VxRail node network adapters	10
3 Topology options	12
3.1 Dual switch	12
3.1.1 Dual switch with VLT	12
3.1.2 Dual switch without VLT	13
3.2 Single switch	14
4 VxRail in the data center	15
4.1 Leaf-spine network	15
4.2 OOB management network	16
5 Configuration planning	17
5.1 VLANs and IP addresses	17
5.2 VxRail network configuration table	18
5.3 Using a jump box or laptop computer	19
5.4 DNS and NTP servers	19
6 Switch configuration prerequisites	21
6.1 Check switch OS version	21
6.2 Verify license installation	21
6.3 Factory default configuration	22
7 Configure switches	23
7.1 Dual switch with VLT	23
7.1.1 General settings	23
7.1.2 Configure VLANs	24
7.1.3 Configure interfaces	25
7.1.4 Configure VLT	26
7.2 Dual switch without VLT	27
7.2.1 General settings	28
7.2.2 Configure VLANs	28
7.2.3 Configure interfaces	29
7.2.4 Configure the switch interconnect	30
7.3 Single switch	31
7.3.1 General settings	32
7.3.2 Configure VLANs	32
7.3.3 Configure interfaces	33
8 Switch validation	36
8.1 General validation commands	36
8.1.1 show interface status	36
8.1.2 show port-channel summary	36
8.1.3 show vlan	37
8.1.4 show lldp neighbors	38
8.1.5 show vrrp brief	39
8.2 VLT validation commands	39
8.2.1 show vlt domain_id	39
8.2.2 show vlt domain_id backup-link	39
8.2.3 show vlt domain_id mismatch	40
9 Deploy VxRail	41
10 Use of VxRail 4.7.0 to validate Dell EMC Networking S5200F-ON	43
A Validated components for S5148F-ON using VxRail 4.5	45
A.1 Dell EMC Networking Switches	45
A.2 DAC Cables	45
A.3 VxRail P570 nodes	45
A.4 VxRail Appliance software	46
B Validated components for S5248F-ON and S5232F-ON using VxRail 4.7.0	47
B.1 Dell EMC Networking switches	47
B.2 DAC Cables	47
B.3 VxRail E560 nodes	47
B.4 VxRail appliance software	48
C VxRail network adapter traffic optimization	49
D Configure breakouts on port groups and interfaces	50
D.1 Breakout port-groups for S5248F-ON	50
D.2 Breakout interfaces for S5232F-ON	51
D.3 Auto-breakout feature	51
E Technical resources	52

Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 43

Use of VxRail 4.7.0 to validate Dell EMC Networking, S5200F-ON

Page 43 highlights