Dell Vostro 5515 Vostro 15 5515 Service Manual - Page 20

Battery cable, Removing the battery cable

Get Dell Vostro 5515 PDF manuals and user guides View all Dell Vostro 5515 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

1. Using the alignment posts, place the 4-cell battery on the palm-rest and keyboard assembly. 2. Align the screw holes on the 4-cell battery with the screw holes on the palm-rest and keyboard assembly. 3. Replace the four (M2x3) screws that secure the 4-cell battery to the palm-rest and keyboard assembly. 4. Connect the battery cable to the system board. 5. Adhere the tape that secures the battery cable to the system board. 1. Install the base cover. 2. Follow the procedure in After working on your computer. Battery cable Removing the battery cable 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the 3-cell battery or 4-cell battery, whichever applicable. NOTE: If battery is disconnected from system board for service, then there is a delay during system boot as the system undergoes RTC battery reset. The following images indicate the location of the battery cable and provide a visual representation of the removal procedure. 1. Flip the battery and remove the battery cable from the routing guides on the battery. 2. Disconnect the battery cable from the connector on the battery. 3. Lift the battery cable off the battery. Installing the battery cable If you are replacing a component, remove the existing component before performing the installation procedure. The following image indicates the location of the battery cable and provides a visual representation of the installation procedure. 20 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
1.
Using the alignment posts, place the 4-cell battery on the palm-rest and keyboard assembly.
2.
Align the screw holes on the 4-cell battery with the screw holes on the palm-rest and keyboard assembly.
3.
Replace the four (M2x3) screws that secure the 4-cell battery to the palm-rest and keyboard assembly.
4.
Connect the battery cable to the system board.
5.
Adhere the tape that secures the battery cable to the system board.
1.
Install the
base cover
.
2.
Follow the procedure in
After working on your computer
.
Battery cable
Removing the battery cable
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
3-cell battery
or
4-cell battery
, whichever applicable.
NOTE:
If battery is disconnected from system board for service, then there is a delay during system boot as the system
undergoes RTC battery reset.
The following images indicate the location of the battery cable and provide a visual representation of the removal procedure.
1.
Flip the battery and remove the battery cable from the routing guides on the battery.
2.
Disconnect the battery cable from the connector on the battery.
3.
Lift the battery cable off the battery.
Installing the battery cable
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of the battery cable and provides a visual representation of the installation procedure.
20
Removing and installing components