Dell Vostro 5625 Service Manual - Page 40

I/O board, Removing the I/O board

Get Dell Vostro 5625 PDF manuals and user guides View all Dell Vostro 5625 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

5. Close the right display hinge and align the screw holes on the right display hinge with the screw holes on the system board. 6. Replace the three screws (M2.5x5) that secure the right display hinge to the palm-rest and keyboard assembly. 7. Replace the display cable to the routing guides on the palm-rest and keyboard assembly. 8. Connect the display cable to the connector on the system board. 9. Close the latch and replace the clear adhesive tape. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. I/O board Removing the I/O board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the 3-cell battery or 4-cell battery, whichever is applicable. About this task NOTE: A RJ-45 Network Port assembly for the I/O board is required. If you are replacing the I/O board, transfer the existing RJ-45 Network Port assembly to the replacement I/O board. The following image(s) indicate the location of the I/O board and provides a visual representation of the removal procedure. 40 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
5.
Close the right display hinge and align the screw holes on the right display hinge with the screw holes on the system board.
6.
Replace the three screws (M2.5x5) that secure the right display hinge to the palm-rest and keyboard assembly.
7.
Replace the display cable to the routing guides on the palm-rest and keyboard assembly.
8.
Connect the display cable to the connector on the system board.
9.
Close the latch and replace the clear adhesive tape.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
I/O board
Removing the I/O board
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
3-cell battery
or
4-cell battery
, whichever is applicable.
About this task
NOTE:
A RJ-45 Network Port assembly for the I/O board is required.
If you are replacing the I/O board, transfer the existing RJ-45 Network Port assembly to the replacement I/O board.
The following image(s) indicate the location of the I/O board and provides a visual representation of the removal procedure.
40
Removing and installing components