Denon AVR-2802 Owners Manual - Page 15

ENGLISH 8 REMOTE CONTROL UNIT • The included remote control unit (RC-904) can be used to operate not only the AVR-2802 but other remote control compatible DENON components as well. In addition, the memory contains the control signals for other remote control units, so it can be used to operate non-Denon remote control compatible products. Inserting the batteries q Remove the remote control unit's rear cover. w Set three R6P/AA batteries in the battery compartment in the indicated direction. e Put the rear cover back on. Notes on Batteries • Use R6P/AA batteries in the remote control unit. • The batteries should be replaced with new ones approximately once a year, though this depends on the frequency of usage. • Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.) • When inserting the batteries, be sure to do so in the proper direction, following the "≈" and "√" marks in the battery compartment. • To prevent damage or leakage of battery fluid: • Do not use a new battery together with an old one. • Do not use two different types of batteries. • Do not short-circuit, disassemble, heat or dispose of batteries in flames. • Remove the batteries from the remote control unit when you do not plan to use it for an extended period of time. • If the battery fluid should leak, carefully wipe the fluid off the inside of the battery compartment and insert new batteries. • When replacing the batteries, have the new batteries ready and insert them as quickly as possible. • The learned remote control signals may be cleared if no batteries are in the remote control unit for about 5 seconds. The factory-installed codes are in permanent memory, however. Using the remote control unit B Approx. 7 m 30° 30° • Point the remote control unit at the remote sensor on the main unit as shown on the diagram. • The remote control unit can be used from a straight distance of approximately 7 meters from the main unit, but this distance will be shorter if there are obstacles in the way or if the remote control unit is not pointed directly at the remote sensor. • The remote control unit can be operated at a horizontal angle of up to 30 degrees with respect to the remote sensor. NOTES: • It may be difficult to operate the remote control unit if the remote sensor is exposed to direct sunlight or strong artificial light. • Do not press buttons on the main unit and remote control unit simultaneously. Doing so may result in malfunction. • Neon signs or other devices emitting pulse-type noise nearby may result in malfunction, so keep the set as far away from such devices as possible. Operating DENON audio components • Turn on the power of the different components before operating them. 1 AUDIO Set mode switch 1 to "AUDIO (AVR/AVC)". AVR/AVC VIDEO 2 TAPE CDR/MD Set mode switch 2 to the position for the CD MULTI component to be operated. DVD TV VDP VCR 1 3 START SYSTEM CALL SET CALL DVD VDP 1 2 TV/DBS 4 5 VCR-1 CD 7 8 VCR-2/V.AUX +10 0 RC-904 LEARNED/TX POWER OFF ON / SOURCE TUNER 3 SHIFT PHONO 6 CDR / TAPE 9 CHANNEL TV/VCR A / B VOLUME DISC SKIP+ SPEAKER DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 6CH STEREO INPUT MODE ANALOG STEREO EXT.IN MASTER VOL. AUDIO TAPE CDR/MD CD MULTI MUTING AVR/AVC VIDEO TUNING DVD TV VDP VCR SYSTEM SETUP SURROUND PARAMETER BAND RDS MODE PTY MEMORY RT TITLE MENU/GUIDE CH SELECT ENTER SELECT STATUS ON SCREEN DISPLAY RETURN USE/LEARN T.TONE MULTI DVD SET UP 3 2 3 Operate the audio component. • For details, refer to the component's operating instructions. While this remote control is compatible with a wide range of infrared controlled components, some models of components may not be operated with this remote control. 1. CD player (CD) and CD recorder and MD recorder (CDR/MD) system buttons 2. Tape deck (TAPE) system buttons VCR-2/V.AUX +10 TV/VCR A / B VCR-2/V.AUX +10 TV/VCR A / B VOLUME DISC SKIP+ VOLUME DISC SKIP+ 6, 7 2 1 8, 9 3 DISC SKIP + : Manual search (forward and reverse) : Stop : Play : Auto search (cue) : Pause : Switch disc (for CD changers only) 6 7 2 1 3 8 A/B : Rewind : Fast-forward : Stop : Forward play : Pause : Reverse play : Switch between decks A and B 3. Tuner system buttons SHIFT CHANNEL +, - SYSTEM CALL SET CALL DVD VDP 1 2 TV/DBS 4 5 VCR-1 CD 7 8 POWER OFF ON / SOURCE TUNER 3 SHIFT PHONO 6 CDR / TAPE 9 CHANNEL : Switch preset channel range : Preset channel up/down * For the tuner only, the following buttons can also be operated: TUNING SYSTEM SETUP SURROUND PARAMETER BAND MODE MEMORY RDS PTY RT TITLE MENU/GUIDE CH SELECT ENTER SELECT STATUS ON SCREEN DISPLAY RETURN TUNING •, ª : Tuning up/down BAND : Switch between AM and FM bands MODE : Switch between auto and mono MEMORY : Preset memory SHIFT : Switch preset channel range RDS : RDS search PTY : PTY search RT : Radio text 15