Denon AVR 689 Owners Manual - English - Page 38

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting Specifications ENGLISH A2 SB CH OUT (for Multi-channel sources) Select playback mode for surround back channels. [Selectable items] OFF : No signal is played from the surround back channels. MTRX ON : The surround channel signals undergo digital matrix processing and are output from the surround back channels. PLIIx C z1 : Decoded in Dolby Pro Logic IIx Cinema mode, surround back signal played. PLIIx M z2 : Decoded in Dolby Pro Logic IIx Music mode, surround back signal played. ES MTRX z3 : DTS signal played with digital matrix processing. ES DSCRT z4 : Signal included in DTS-ES Discrete 6.1-channel sources played. z1: This can be selected when "Surround Back Speaker" is set to "2spkrs" at the "System Setup" - "Speaker Setup" setting (vpage 23). z2: This can be selected when "Surround Back Speaker" is set to "2spkrs" or "1spkr" at the "System Setup" - "Speaker Setup" setting. z3: This can be selected when playing DTS sources. z4: This can be selected when playing DTS sources including a discrete 6.1-channel signal identification signal. Settings can also be made when [STD] is pressed. When using surround back speakers, adopt the following settings. q Adopt "7.1ch" for the Amp Assign setting. • The default setting for the Amp Assign mode of AVR-689 is "ZONE2". w Adopt a setting other than "OFF" for the "SB CH OUT" setting of "Surround Parameter". A2 SB CH OUT (for 2-channel sources) Determine whether to use surround back speakers. [Selectable items] ON : The surround back channel signal is played. OFF : The surround back channel signal is not played. A3 SW ATT (Subwoofer Attenuation) Attenuate subwoofer level when using EXT. IN mode. [Selectable items] ON : The input from the subwoofer channel is attenuated. OFF : The input from the subwoofer channel is not attenuated. Usually use in this mode. Set this to "ON" if the subwoofer channel level seems too high when playing audio signal. A4 Subwoofer Turn subwoofer output on and off. [Selectable items] ON : The subwoofer is used. OFF : The subwoofer is not used. A5 Tone Control Turn tone adjustments on and off. [Selectable items] ON : Allow tone adjustment (treble, bass). OFF : Playback without tone adjustment. The tone cannot be adjusted when in the DIRECT mode. NOTE When the "Dynamic EQ" setting is "ON", setting is not possible. A6 Bass Adjust low frequency range (bass). [Variable range] -6dB ~ 0dB ~ +6dB A7 Treble Adjust high frequency range (treble). [Variable range] -6dB ~ 0dB ~ +6 dB A8 MultEQ Select the type of room correction desired from the following list: [Selectable items] Audyssey : Optimize frequency response of all speakers. Byp. L/R : Optimize frequency response of speakers except front L and R speakers. Flat : Optimize frequency response of all speakers to flat response. OFF : Turn equalizer off. Audyssey Audyssey Byp. L/R OFF Audyssey Flat Operating from the main unit or remote control unit Press MULTEQ. • When "Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected, the Audyssey MultEQ indicator lights green. • After running Auto Setup, if the Speaker Configuration, Distance, Channel Level and Crossover Frequency have changed without increasing the number of speakers measured, the Audyssey MultEQ indicator lights red. NOTE • "MultEQ" can only be set when Auto Setup has been performed. • "MultEQ" cannot be set in the following situations. • If "Auto Setup" fails to be completed. • After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. • If the settings of speakers for which "None" has been determined at "Auto Setup" are changed, "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" cannot be selected. Either perform Auto Setup again, or return to the setting after running Auto Setup with "System Setup" - "Speaker Setup" - "Restore". • When using headphones, "MultEQ" is set to "OFF". "Bass" and "Treble" can be set when "Tone Control" is set to "ON". 35 For details on adjusting individual parameters, see "Adjusting the parameters" (vpage 33).