Dewalt DCMWP234U2 Instructional Manual - Type 1 - Page 18

English Wall Mounting Some DeWALT chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or other obstructions which may impede air flow. Use the back of the charger as a template for the location of the mounting screws on the wall. Mount the charger securely using drywall screws (purchased separately) at least 1" (25.4 mm) long, with a screw head diameter of 0.28-0.35" (7-9 mm), screwed into wood to an optimal depth leaving approximately 7/32" (5.5 mm) of the screw exposed. Align the slots on the back of the charger with the exposed screws and fully engage them in the slots. SAVE THESE INSTRUCTIONS FOR FUTURE USE ASSEMBLY AND ADJUSTMENTS  DANGER: To reduce the risk of serious personal injury, turn unit off and remove the safety key and battery packs before making any adjustments or removing/installing attachments or accessories. An accidental start‑up can cause injury. Single Touch Handle Adjustments (Fig. D, E) The mower is shipped in the storage position. You will need to adjust the single touch handle 1 to the operating position before continuing. Raise the Single Touch Handle (Fig. D) 1. To unlock the single touch handle 1 from the storage position, squeeze the handle unlock button 3 . NOTE: The handle unlock button 3 is located on the back of handle support 2 . NOTE: The main handle 4 must pop out slightly from both sides of the single touch handle tubes before lifting the single touch handle 1 from the storage position as shown in Fig. D,. 2. Raise the single touch handle 1 to the locked position. Listen for an audible click and ensure the single touch handle 1 is locked into position before proceeding. 3. Extend the main handle 4 outward until a set of audible clicks is heard. The single touch handle 1 is now in the operation position. NOTE: Take care to not pinch, pull or otherwise stress the cord 28 . Adjusting the Main Handle Height (Fig. F) The main handle 4 extends to accommodate taller users. 1. To extend the main handle 4 to the lower height position, press the handle release button 5 and pull the main handle away from the handle support 2 until an audible click is heard, indicating that it is locked into the lower height position. NOTE: The handle release button 5 is located on the bottom of handle support 2 . 2. To extend the main handle 4 to the upper height position, press the handle release button 5 and pull the 16 main handle away from the handle support 2 until an audible click is heard, indicating that it is locked into the upper height position. 3. Ensure the main handle 4 locks into position before proceeding. NOTE: When the batteries 26 and safety key 6 are inserted and the bail handle 8 is pulled, the handle folding indicator 15 will illuminate if the single touch handle 1 is not locked into position. 4. To retract the main handle 4 to the lower height postion, press the handle release button 5 and push the main handle 4 towards the handle support 2 until an audible click is heard, indicating that it is locked into the lower height position. Storage Mode (Fig. G-L)  DANGER: MAKE CERTAIN THE SAFETY KEY IS REMOVED TO PREVENT ACTUATION BEFORE REMOVING OR INSTALLING BATTERIES.  DANGER: Turn unit off and remove safety key and battery packs. 1. To retract the main handle 4 , press the handle release button 5 and push the main handle 4 towards the handle support 2 until two audible clicks are heard, indicating that both sides of the handles are locked into position. The main handle 4 must be fully seated against the handle support. NOTE: The main handle 4 must fully engage the handle windows 29 . If they are not engaged as shown in Fig. G, press the main handle 4 towards the handle support 2 until two audible clicks are heard and both sides of handle windows 29 are closed as shown in Fig. H. NOTE: Ensure the two storage latches 30 at the back of the single touch handle 1 tubes pop outward as shown in Fig. J before lowering the single touch handle 1 into the stoarge position. 2. Fold the single touch handle 1 towards the front wheels 32 into storage position. Listen for two audible clicks as the two storage latches 30 slide into the storage slots 31 as shown in Fig. K. 3. Ensure the single touch handle 1 is locked into storage position before proceeding. 4. The mower can be stored standing up, with the collection bag removed, or flat on its wheels as shown in Fig. L. NOTE: Take care to not pinch, pull or otherwise stress the cord 28 . Grass Collection Bag (Fig. M)  DANGER: Turn unit off and remove safety key and battery packs. 1. Lift the rear door cover 21 , remove mulching plug 24 , and place the grass collection bag 22 onto the mower so the bag lugs 33 slide into the slots 39 on the inside plastic surfaces of the handle brackets. Then lower the rear door cover 21 . NOTE: If installed, remove rear side discharge chute 25 and ensure the rear door cover 21 is fully up before installing grass collection bag 22 .