EVGA 113-YW-E115-TR User Manual - Page 27

Connecting Serial ATA Cables

Get EVGA 113-YW-E115-TR PDF manuals and user guides View all EVGA 113-YW-E115-TR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Connecting Serial ATA Cables The Serial ATA II connector is used to connect the Serial ATA II device to the motherboard. These connectors support the thin Serial ATA II cables for primary storage devices. The current Serial ATA II interface allows up to 300MB/s data transfer rate. There are eight (8) serial ATA II connectors on the motherboard. SATA ports 1 through 3 support RAID 0, RAID 1, RAID 5, RAID 0+1 and JBOD configurations. The SATA 4 port uses the JMicron JMB363 and only supports RAID 0, RAID 1. TX- TX- RX+ GND GND TX+ GND SATA 3 SATA C1 (top) SATA C0 (bottom) SATA 2 SATA B1 (top) SATA B0 (bottom) SATA 4 SATA D1 (top) SATA D0 (bottom) SATA 1 SATA A1 (top) SATA A0 (bottom) Note: The SATA3 port only supports AHCI and RAID mode. It does not support IDE mode. Connect the locking cable end to the motherboard connector. Connect the end without the lock to the drive. EVGA 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
EVGA
16
Connecting Serial ATA Cables
The Serial ATA II connector is used to connect the Serial ATA II device to the
motherboard. These connectors support the thin Serial ATA II cables for
primary storage devices. The current Serial ATA II interface allows up to
300MB/s data transfer rate.
There are eight (8) serial ATA II connectors on the motherboard. SATA ports 1
through 3 support RAID 0, RAID 1, RAID 5, RAID 0+1 and JBOD
configurations. The SATA 4 port uses the JMicron JMB363 and only supports
RAID 0, RAID 1.
Note:
The SATA3 port only supports AHCI and RAID
mode. It does not support IDE mode.
SATA 3
SATA C1 (top)
SATA C0 (bottom)
Connect the locking cable
end to the motherboard
connector.
Connect the end without
the lock to the drive.
SATA 1
SATA A1 (top)
SATA A0 (bottom)
SATA 2
SATA B1 (top)
SATA B0 (bottom)
SATA 4
SATA D1 (top)
SATA D0 (bottom)
GND
TX-
RX+
GND
TX-
TX+
GND