Electrolux EI30MH55GB Service Manual - Page 33
REMOVAL OF OVEN FROM WALL Two persons recommended to remove the oven, OUTER CASE REMOVAL, HOOD FAN
UPC - 012505558610
View all Electrolux EI30MH55GB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 33 highlights
4. Remove the three (3) screws holding the hood louver to the oven cavity front face plate and the outer case screw at the top middle. 5. Pull the hood louver from the oven cavity by pushing the right and left tabs of the hood louver to remove. 6. Now, the hood louver is free. Screws Left tab Right tab EI30MH55GSA EI30MH55GBA EI30MH55GWA Hood louver REMOVAL OF OVEN FROM WALL (Two persons recommended to remove the oven) 1. Disconnect the power supply cord, and uncoil the power supply cord. 2. To discharge the high voltage capacitor, wait for 60 seconds. 3. If the exhaust damper assembly is installed, remove the one (1) screw holding the exhaust damper assembly to the rear stay, and remove the exhaust damper assembly by sliding it backward. 4. Remove the two (2) screws holding the oven (outer case cabinet) to the top cabinet. 5. While supporting the front of the oven, pull down the two (2) mounting levers and release the oven from the unit mounting plate. 6. Pull the power cord out of the wall cabinet and remove the oven. 7. The oven is now free and can be placed on the work surface selected for servicing the oven. 8. Installation is the reverse of this procedure. OUTER CASE REMOVAL Remove the oven from the wall, referring to "removal of 7. Disconnect the three (3) pin connector of the power oven from wall" and proceed as follows; supply cord from the wiring harness and remove the 1. Disconnect the power supply cord. power supply cord together with the outer case. 2. Open the door and block it open. 8. Nip the cord bushing with bushing pliers and release it 3. To discharge the high voltage capacitor, wait for 60 from the outer case cabinet. seconds. 9. Remove the cord bushing and the power supply cord 4. Remove five (5) screws holding the rear stay to the outer from the outer case cabinet. case cabinet, hood fan motor or the oven, and remove 10.Now, the power supply cord or the outer case cabinet is it. free. 5. Remove the six (6) screws from the rear of the outer CAUTION: 1. Disconnect oven from power case cabinet and one (1) screw at front. supply before removing outer 6. Slide the outer case cabinet back about 1 inch (3 cm) case. to free it from retaining clips on the cavity face plate. 2. Discharge the high voltage capacitor before touching any oven components or wiring. HOOD FAN MOTOR REMOVAL 1. Disconnect the power supply cord and remove the oven from the main wire harness located at the right edge of from wall and remove outer case. (Refer to procedure the oven cavity top plate and release the snap band from of "Removal of Oven from Wall" and "Outer case the hood duct. Removal") 5. Remove the hood fan motor from the oven cavity top 2. Open the door and block it open. plate by lifting it up. 3. To discharge the high voltage capacitor, wait for 60 6. Now, the hood fan motor is free. seconds. 4. Disconnect the 6-pin connector of the hood fan motor MAGNETRON REMOVAL 1. Disconnect the power supply cord , remove the oven from wall and remove outer case (Refer to procedure of "Removal of Oven from Wall" and "Outer case Removal".) 2. Open the door and block it open. 3. To discharge the high voltage capacitor, wait for 60 seconds. 4. Remove the seven (7) screws holding the hood intake duct R to the oven cavity top plate, the oven cavity front flange, the fan duct and magnetron duct. And remove the hood intake duct R. 5. Disconnect the high voltage wire from the magnetron. 6. Release the two (2) tabs of the fan duct from the base plate R. 7. Remove the magnetron duct from the oven cavity, by releasing the tab of the magnetron duct from the base plate R. 8. Remove the grease filter (right side one) from the base cover. 9. Carefully remove four (4) mounting screws holding the magnetron to waveguide. When removing the screws hold the magnetron to prevent it from falling. 10.Remove the magnetron from the unit with care so the magnetron tube should not be hit by any metal object around the tube. CAUTION: WHEN REPLACING THE MAGNETRON, BE SURE THE R.F. GASKET IS IN PLACE AND MOUNTING SCREWS ARE TIGHTENED SECURELY. 33