Electrolux EI30MH55GB Service Manual - Page 38
Stop Switch, Primary Interlock Switch, Secondary Interlock Switch And, Monitor Switch Removal,
UPC - 012505558610
View all Electrolux EI30MH55GB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 38 highlights
EI30MH55GSA EI30MH55GBA EI30MH55GWA STOP SWITCH, PRIMARY INTERLOCK SWITCH, SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL 1. Disconnect the power supply cord and remove the oven from wall and remove outer case. (Refer to procedure of "Removal of Oven from Wall" and "Outer case Removal") 2. Open the door and block it open. 3. To discharge the high voltage capacitor, wait for 60 seconds. 4. Remove the seven (7) screws holding the hood intake duct R to the oven cavity top plate, the oven cavity front flange, fan duct, base plate R and magnetron duct. And remove the hood intake duct R. 5. Remove the control panel assembly, referring to the procedure of "CONTROL PANEL ASSEMBLY , CONTROL UNIT AND KEY UNIT REMOVAL". 6. Remove the two (2) screws holding the latch hook to the oven cavity front flange. 7. Remove the latch hook from the oven cavity front flange. 8. Disconnect the wire leads of each switch. 9. Remove each switch from the latch hook by pushing the one (1) stopper tab holding each switch. 10.Now, each switch is free. Re-install 1. Re-install each switch in its place.The secondary interlock switch is in the lower position, stop switch is in the upper position and the primary interlock switch is the upper position under the stop switch. And the monitor switch is in the middle position. 2. Re-connect wire leads to each switch. Refer to pictorial diagram. 3. Secure the latch hook (with two (2) mounting screws) to oven cavity front flange. 4. Make sure that the monitor switch is operating properly and check continuity of the monitor circuit. Refer to chapter "Test Procedure" and "Adjustment procedure". STOP SWITCH, PRIMARY INTERLOCK SWITCH, SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT 1. Disconnect the power supply cord and remove the oven from wall and remove outer case. (Refer to procedure of "Removal of Oven from Wall" and "Outer case Removal") 2. Open the door and block it open. 3. To discharge the high voltage capacitor, wait for 60 seconds. 4. Remove the seven (7) screws holding the hood intake duct R to the oven cavity top plate, the oven cavity front flange, fan duct, base plate R and magnetron duct. And remove the hood intake duct R. 5. Remove the control panel assembly, referring to the procedure of "CONTROL PANEL ASSEMBLY , CONTROL UNIT AND KEY UNIT REMOVAL". If the stop switch, primary interlock switch, secondary interlock switch and monitor switch do not operate properly due to a misadjustment, the following adjustment should be made. 6. Loosen the two (2) screws holding latch hook to the oven cavity front flange. 7. With door closed, adjust latch hook by moving it back and forth, and up and down. In and out play of the door allowed by the upper and lower position of the latch hook should be less than 0.5mm. The vertical position of the latch hook should be adjusted so that the secondary interlock switch and primary interlock switch are activated with the door closed. The horizontal position of the latch hook should be adjusted so that the monitor switch and stop switch are activated with the door closed. 8. Secure the screws with washers firmly. 9. Check all of the switches operation. If any switch has not activated with the door closed, loosen screw and adjust the latch hook position. After adjustment, check the following. 1. In and out play of door remains less than 0.5mm when in the latched position. First check upper position of latch hook, pushing and pulling upper portion of door toward the oven face.Then check lower portion of the latch hook, pushing and pulling lower portion of the door toward the oven face. Both results (play in the door) should be less than 0.5mm. 2. The secondary interlock switch and primary interlock switch interrupt the circuit before the door can be opened. 3. Monitor switch contacts close when door is opened. 4. Stop switch contacts open when door is opened. 5. Re-install outer case and check for microwave leakage around door with an approved microwave survey meter. (Refer to Microwave Measurement Procedure.) Latch heads Latch hook Door Stop switch Primary interlock switch Open lever Monitor switch Secondary interlock switch Figure C-1. Latch Switch Adjustments 38