Epson Equity II Product Support Bulletin(s) - Page 67

Epson America Inc.

Get Epson Equity II PDF manuals and user guides View all Epson Equity II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

EPSON EPSON AMERICA INC. SERVICE DEPARTMENT PRODUCT SUPPORT BULLETIN DATE: 3/16/87 NUMBER: S-0007 SUBJECT: EQUITY II PROBLEMS DUE TO IMPROPER DIPSWITCH SETTINGS We would like to make you aware of a couple of different problems caused by improperly set dip switches on the Equity II computer. Some customers have complained about Lotus 123 version 2.0 not running properly on the Equity II with the latest version ROM BIOS and MS-DOS. The cause of the problems was determined to be that the co-processor switch (S1-2) was in the wrong position. It was switched "OFF" without a co-processor chip installed when it should have been in the "ON" position. After setting the switch correctly and rebooting the system the software ran normally. This may also affect the operation of other software packages although we have not had any other reports. Another problem was that after installing a hard drive in an Equity II the system displayed Drive D: instead of Drive C:, The problem was that the person who installed the hard disk drive forgot to reconfigure the dip switches for 1 floppy drive. This question has come up quite a few times. ***** CHECK THOSE DIP SWITCHES!! ***** Page 1 of 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
EPSON
EPSON AMERICA INC.
SERVICE DEPARTMENT
PRODUCT
SUPPORT
BULLETIN
DATE: 3/16/87
NUMBER:
S-0007
SUBJECT: EQUITY II PROBLEMS DUE TO IMPROPER DIPSWITCH SETTINGS
We would like to make you aware of a couple of different problems
caused by improperly set dip switches on the Equity II computer.
Some customers have complained about Lotus 123 version 2.0 not
running properly on the Equity II with the latest version ROM
BIOS and MS-DOS.
The cause of the problems was determined to be that the
co-processor switch (S1-2) was in the wrong position.
It was
switched
"OFF"
without a co-processor chip installed when it
should have been in the "ON"
position. After setting the switch
correctly and rebooting the system the software ran normally.
This may also affect the
operation of other
software packages
although we have not had any other reports.
Another
problem
was
that
after
installing a hard drive in an
Equity II the system displayed Drive D: instead of Drive C:,
The problem was that the person who installed the hard disk drive
forgot to reconfigure the dip switches
for 1
floppy drive. This
question has come up quite a few times.
***** CHECK THOSE DIP SWITCHES!! *****
Page 1 of 1