Epson Equity II Product Support Bulletin(s) - Page 74

H. See Product Support Bulletin S-0020 for set-up information.

Get Epson Equity II PDF manuals and user guides View all Epson Equity II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

1 NUMBER: S-0001C PAGE: 2 of 5 I JU-595-10 PANASONIC COMMENT CODE EXPLANATIONS: A. Requires insulating sheet when installed in lower position in Equity II. See TIB Equity 11-006. B. Jumper block SS1 - Position DS0 for drive A, DS1 for drive B C. Equity I must have ROM BIOS version 2.21(MSA-B4) and MS-DOS 2.11 Release 1.04 or higher to use this drive. D. Must set drive select jumpers on FDD logic board for A (position S1) or B (position S2). E. It is not necessary to remove the terminating resistor pack. F. Handle drive with care - possibility of short circuit between screw head on frame and FDD logic board (could damage FDD)! G. Terminator must be removed when used as 2nd floppy drive unit. H. See Product Support Bulletin S-0020 for set-up information. I. Same as MD-5201-57 except comes configured as 2nd drive. J. Jumper block JJ1 - Position S1 for drive A, S2 for drive B.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
1
NUMBER:
S-0001C
PAGE:
2 of 5
I
JU-595-10
PANASONIC
COMMENT CODE EXPLANATIONS:
A. Requires insulating sheet when installed in lower position in
Equity
II.
See TIB Equity 11-006.
B. Jumper block
SS1
- Position DS0 for drive A, DS1 for drive B
C. Equity
I
must have ROM BIOS version 2.21(MSA-B4) and MS-DOS 2.11
Release 1.04 or higher to use this drive.
D. Must set drive select jumpers on FDD logic board for A
(position S1) or B (position S2).
E.
It
is not necessary to remove the terminating resistor pack.
F. Handle drive with care - possibility of short circuit between
screw head on frame and FDD logic board (could damage FDD)!
G. Terminator must be removed when used as 2nd floppy drive unit.
H. See Product Support Bulletin S-0020 for set-up information.
I.
Same as MD-5201-57 except comes configured as 2nd drive.
J.
Jumper block
JJ1
- Position S1 for drive A, S2 for drive B.