Epson Perfection 610 Scanner Basics - Page 61

Software Problems, If you see the message Scanner Not Ready Windows 98 or Cannot find - windows 7 drivers

Get Epson Perfection 610 PDF manuals and user guides View all Epson Perfection 610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

If you see the message "Scanner Not Ready" (Windows 98) or "Cannot find the scanner on the bus" (Macintosh)" . . . s Make sure the scanner is plugged in. You may need to restart your computer after plugging in your scanner. s Make sure your scanner cable is securely connected. Then open and close the scanner monitoring utility to manually check for the scanner (see "Enabling Scanner Monitoring" in your EPSON TWAIN User's Guide). If you still see the message, unplug your scanner, then plug it in again, and restart your system. s To turn off scanner monitoring, see "Enabling Scanner Monitoring" in your EPSON TWAIN User's Guide. Software Problems If you can't open the EPSON TWAIN driver . . . s Check the USB cable connection. If necessary, restart your computer. s Check that your system recognizes your scanner. Check System Device Manager in the Windows Control Panel. s Check your scanner source setting. Make sure you selected EPSON TWAIN L. If the scanner software doesn't work properly . . . s Make sure your computer meets the system requirements listed on pages 3 and 4, and supports the software applications you are using. s Check your computer's memory. See if the computer has enough memory for your software. If you're running other software at the same time, using RAM resident programs, or have many device drivers, the computer may not have enough memory. (See your software and computer manuals.) If you are scanning a large image or scanning at a high resolution, your computer may not have enough memory to process the image. s Check your software installation. Make sure that your software is correctly installed and set up. If all else fails, uninstall your software, then reinstall it. 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
56
If you see the message “Scanner Not Ready” (Windows 98) or “Cannot find the
scanner on the bus” (Macintosh)” . . .
■
Make sure the scanner is plugged in. You may need to restart your computer after
plugging in your scanner.
■
Make sure your scanner cable is securely connected. Then open and close the
scanner monitoring utility to manually check for the scanner (see “Enabling
Scanner Monitoring” in your
EPSON TWAIN User’s Guide
). If you still see the
message, unplug your scanner, then plug it in again, and restart your system.
■
To turn off scanner monitoring, see “Enabling Scanner Monitoring” in your
EPSON TWAIN User’s Guide
.
Software Problems
If you can’t open the EPSON TWAIN driver . . .
■
Check the USB cable connection. If necessary, restart your computer.
■
Check that your system recognizes your scanner. Check System Device Manager
in the Windows Control Panel.
■
Check your scanner source setting. Make sure you selected
EPSON TWAIN L
.
If the scanner software doesn’t work properly . . .
■
Make sure your computer meets the system requirements listed on pages 3 and 4,
and supports the software applications you are using.
■
Check your computer’s memory. See if the computer has enough memory for
your software. If you’re running other software at the same time, using RAM
resident programs, or have many device drivers, the computer may not have
enough memory. (See your software and computer manuals.) If you are scanning
a large image or scanning at a high resolution, your computer may not have
enough memory to process the image.
■
Check your software installation. Make sure that your software is correctly
installed and set up. If all else fails, uninstall your software, then reinstall it.