Epson PowerLite 1825 Product Information Guide - Page 12

Replacing the Lamp and Air Filter - ceiling mount

Get Epson PowerLite 1825 PDF manuals and user guides View all Epson PowerLite 1825 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

PowerLite 1825 You can remove the air filter to clean both sides even if the projector is mounted on the ceiling (see below). Vent Air filter 3. If the dirt is difficult to remove or the filter is broken, replace the filter as described below. Contact your dealer or call Epson at 800-GO-EPSON (800-463-7766) to obtain a new filter (part number V13H134A08). Replacing the Lamp and Air Filter The life span of the projection lamp is about 2,500 hours if Brightness Control in the Settings menu is set to High (default), and 3,000 hours if Brightness Control is set to Low. Note: When you get a replacement lamp for your projector, you should replace the filter. Turn off this product when not in use to prolong the life of the projector. It is time to replace the lamp when: ❏ The projected image gets darker or starts to deteriorate. ❏ The message Replace the lamp appears on the screen when the lamp comes on and the lamp warning light flashes orange. To maintain projector brightness and image quality, replace the lamp as soon as possible. ❏ The lamp warning light out). flashes red (the lamp is burnt Follow these steps to replace the lamp and air filter: 1. Turn off the projector and unplug the power cord. 2. Let the projector cool for at least an hour (if it has been on). The lamp is extremely hot immediately after use. Warning: Let the lamp cool fully before replacing it. In the unlikely event that the lamp has broken, small glass fragments may be present and should be removed carefully to avoid injury. If the lamp is used after the replacement period has passed, the possibility that the lamp may break increases. When a lamp replacement message appears, replace the lamp with a new one as soon as possible, even if it is still working. 3. Loosen (but don't remove) the lamp cover screw. Then slide the lamp cover to the side and lift it off the projector. 4. Loosen the two screws holding the lamp in place. Loosen, but don't remove these screws Lamp warning light 5. Hold the lamp as shown and pull it straight out. To obtain a new lamp, contact your dealer or call Epson at 800-GO-EPSON (800-463-7766). Request part number V13H010L40. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 12 2/08

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
PowerLite 1825
12
2/08
You can remove the air filter to clean both sides even if the
projector is mounted on the ceiling (see below).
3.
If the dirt is difficult to remove or the filter is broken,
replace the filter as described below. Contact your dealer or
call Epson at 800-GO-EPSON (800-463-7766) to obtain a
new filter (part number V13H134A08).
Replacing the Lamp and Air Filter
The life span of the projection lamp is about 2,500 hours if
Brightness
Control
in the Settings menu is set to
High
(default), and 3,000 hours if
Brightness
Control
is set to
Low
.
Note:
When you get a replacement lamp for your projector, you
should replace the filter. Turn off this product when not in use to
prolong the life of the projector.
It is time to replace the lamp when:
❏
The projected image gets darker or starts to deteriorate.
❏
The message
Replace the lamp
appears on the screen when
the lamp comes on and the lamp warning light
flashes
orange. To maintain projector brightness and image quality,
replace the lamp as soon as possible.
❏
The lamp warning light
flashes red (the lamp is burnt
out).
To obtain a new lamp, contact your dealer or call Epson at
800-GO-EPSON (800-463-7766). Request part number
V13H010L40.
Follow these steps to replace the lamp and air filter:
1.
Turn off the projector and unplug the power cord.
2.
Let the projector cool for at least an hour (if it has been on).
The lamp is extremely hot immediately after use.
Warning:
Let the lamp cool fully before replacing it. In the
unlikely event that the lamp has broken, small glass fragments
may be present and should be removed carefully to avoid injury.
If the lamp is used after the replacement period has passed, the
possibility that the lamp may break increases. When a lamp
replacement message appears, replace the lamp with a new one
as soon as possible, even if it is still working.
3.
Loosen (but don’t remove) the lamp cover screw. Then slide
the lamp cover to the side and lift it off the projector.
4.
Loosen the two screws holding the lamp in place.
5.
Hold the lamp as shown and pull it straight out.
Note
:
The lamp(s) in this product contain mercury. Please
consult your state and local regulations regarding disposal or
recycling. Do not put in the trash.
Air filter
Vent
Lamp
warning
light
Loosen, but don’t
remove these screws