Fisher and Paykel DE4024P2 User Guide - Page 34

TIME TO GO, displayed in 'TIME

Get Fisher and Paykel DE4024P2 PDF manuals and user guides View all Fisher and Paykel DE4024P2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

TROUBLESHOOTING PROBLEM No numbers displayed during cycle, only lights. POSSIBLE CAUSES Dryer is continuously monitoring the amount of moisture in the clothes. 'TIME TO GO' jumped to a lower number. The estimated time may change when a smaller load than usual is being dried. Cannot make a selection and the dryer beeps twice. The dryness level, temperature, or option that you are trying to select is incompatible with the chosen dry cycle. Dryer is running but is displayed in 'TIME TO GO'. The 'Wrinkle Free', 'Extra' option was chosen. Clean lint filter (message). 'POWER' button was activated. Dryer doesn't heat. Fuse is blown/circuit breaker is tripped; the dryer may tumble but not heat. Inconsistent drying times. Type of load and drying conditions. Glow at the rear of the drum. Excess debris has collected in the condenser preventing proper airflow. Heaters behind the drum. WHAT TO DO This is normal. When the dryer senses a low level of moisture in the load, the dryer will display the dry time remaining. This is normal. This is normal. This is normal. During extended tumbling, the time remaining is not displayed. Press to begin a dry cycle and the message will disappear. Check the building's fuse/circuit breaker box and replace both fuses or reset both breakers. Your dryer may tumble if only one fuse is blown or one breaker tripped. The load size, types of fabric, wetness of clothes and the condition of the lint filter, condenser, and/or air intake vent located on the front of the dryer will affect drying times. Refer to the 'Caring for your dryer' section. This is normal. Under certain drying conditions and room ambient lighting, the glow of the heaters may be visible at the rear of the drum. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
32
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSES
WHAT TO DO
No numbers
displayed during
cycle, only lights.
Dryer is continuously
monitoring the amount of
moisture in the clothes.
This is normal. When the dryer
senses a low level of moisture in
the load, the dryer will display the
dry time remaining.
‘TIME TO GO’
jumped to a lower
number.
The estimated time may
change when a smaller load
than usual is being dried.
This is normal.
Cannot make a
selection and the
dryer beeps twice.
The dryness level,
temperature, or option that
you are trying to select
is incompatible with the
chosen dry cycle.
This is normal.
Dryer is running
but
is
displayed in ‘TIME
TO GO’.
The ‘Wrinkle Free’, ‘Extra’
option was chosen.
This is normal. During extended
tumbling, the time remaining is
not displayed.
Clean lint filter
(message).
‘POWER’ button was
activated.
Press
to begin a dry cycle and
the message will disappear.
Dryer doesn’t
heat.
Fuse is blown/circuit
breaker is tripped; the dryer
may tumble but not heat.
Check the building’s fuse/circuit
breaker box and replace both fuses
or reset both breakers. Your dryer
may tumble if only one fuse is
blown or one breaker tripped.
Inconsistent
drying times.
Type of load and drying
conditions.
The load size, types of fabric,
wetness of clothes and the condition
of the lint filter, condenser, and/or air
intake vent located on the front of
the dryer will affect drying times.
Excess debris has collected
in the condenser preventing
proper airflow.
Refer to the ‘Caring for your dryer’
section.
Glow at the rear
of the drum.
Heaters behind the drum.
This is normal. Under certain drying
conditions and room ambient
lighting, the glow of the heaters may
be visible at the rear of the drum.