Frigidaire FFMV1645TH Installation Instructions - Page 20

Installation Overview, Attach The Mounting, Plate To The Wall, Non-vented Ductless

Get Frigidaire FFMV1645TH PDF manuals and user guides View all Frigidaire FFMV1645TH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installation Instructions C RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Blower Plate C4. Mount the Microwave Oven C5. Install or change Charcoal Filter IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration. • Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched. IRRBNmTNhoEEEOiusTFAAnTRtHORDiEenaEgR:rW ApIWEITlNaNAatPeDIlSLlSaTRTLnFeVOdAmTOEtLpCoELlLaRlEMLotAeYcOEPaTstDeW IeLIMrOvItAhNePNTeTsGOHhtEoIoNER.rW pizoSToDsInTiTAtIitoaRRHNnl UEeTtThxCCheHTaTbTOuIoSsIItOOttomNNSS outlet. 1. Use a level to check that the template is positioned 0los32ocf..c1rtDLatraaehhiogct6rwesaiiccholtt'luaumtnmdhrtdsseaioooc,iIdttfluradeeoneoinnsrlsroywitodltte.ilihamnfldamievntpthef3heasioe.r/erumr1ukMtcp6mapleapay"nnawtlrthiiktrenlieetoktodhtreaalwelidsutanoostfsetolgsooeua.rgtcnddualwaeeddtttooi,islbtoeoidtoosnuadrnulsidstlsaspl.t.colp5Wo,rno/nee8hrevwt"tehethswrehne.oeollFlyeteohwofssdterepofrhioaegrocrhilesetds toggle bolts. 016'DO NOT INSTALL THE MOUNTING PLATE 54A..TRRinTeesHvmtaiIeSollwavTteitIohMtnheEesI.nitteusmtaatpliloalantit.oenfrIonmstrtuhcetiroenabr owoakll.for your Darle vuelta a la hoja para consultar la versión en Español. Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF MSTHPAAERCKCEETDNHTTEOELRGOLGCINLAEET.IBOONLFTOSRIN2TAHDEDMITOIOUNNATLIN, EGVPELNALTYE AREA. Trim the rear wall template along the dotted line. 3/8" TO EDGE 12" 4" (%716716756+&('14':**1#47+

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
INSTALLATION OVERVIEW
C1.
Attach Mounting Plate to Wall
C2.
Prepare Top Cabinet
C4.
C5.
Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
•
Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
Installation Instructions
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE:
Before tightening toggle bolts and wood
screw, make sure the bott
m of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION:
Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
4
3
ATTACH THE MOUNTING
PLATE TO THE WALL
C1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to
3
/
4
″
(19 mm) onto
each bolt.
1
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
2
RECIRCULATING
(Non-Vented Ductless)
C
Install or change Charcoal Filter
C3.
Check Blower Plate
NOTE:
Cabinet
Cabinet
If the cabinet depth including the cabinet doors
is more than 13
"
'' then the unit must be spaced
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust±intake.
o
EN-20
IMPORTANT :Do not remove the cardboard
etween the heat shield and door.
spacers b