Fujitsu Fi-4750c Operating Guide - Page 32

Setting the SCSI ID and the SCSI Terminator, Press the Next

Get Fujitsu Fi-4750c - Color Duplex Document Scanner 50ppm 90ipm Ccd/scsi PDF manuals and user guides
UPC - 097564303531
View all Fujitsu Fi-4750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Setting the SCSI ID and the SCSI Terminator The default of the SCSI ID is 5. The SCSI ID is set by using the Setup mode of the operator panel. The procedure to change the SCSI ID is as follows: 1 Turn the power On by pressing the "I" side of the power switch (see Figure 1.1). The scanner displays "Scanner Ready" on the lower line of the LCD. 2 Then press the "Next" button. The scanner displays "Mode select 1". 3 Then press the "Next" button twice. The scanner displays "Mode select 2" meaning that the setup mode is ready. 4 Then press the "Enter" button several times. The scanner displays the following: 5 Press the "Next" button several times, then the scanner displays "SCSI ID" on the upper line of the LCD. 6 Select the wished SCSI ID by pressing the " "or " " button, and press "Enter" (the SCSI ID is set.) 7 Press "Exit" to return to the "Scanner Ready" screen if you don't need to change the SCSI terminator. NOTICE If no other device is using the same SCSI ID, the scanner ID does not have to be changed. NOTICE The new ID does not take effect until the system power is turned On again. 8 Press "Next" , then the scanner displays "Terminator" on the upper line of the LCD. Select "On" or "Off" by pressing or , then press "Enter". NOTICE The scanner includes a SCSI terminator that can be turned On and Off from the operator panel of the scanner. The factory default is "On." 9 Press "Exit" to return to the "Scanner Ready" state. 2-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
2-7
Setting the SCSI ID and the SCSI Terminator
The default of the SCSI ID is 5. The SCSI ID is set by using the Setup mode of the operator panel. The
procedure to change the SCSI ID is as follows:
1
Turn the power On by pressing
the “I” side of the power switch
(see Figure 1.1). The scanner
displays “Scanner Ready” on the
lower line of the LCD.
2
Then press the “Next”
button.
The scanner displays “Mode
select 1”.
3
Then press the “Next”
button
twice. The scanner displays
“Mode select 2” meaning that
the setup mode is ready.
4
Then press the “Enter” button
several times. The scanner
displays the following:
5
Press the “Next”
button
several times, then the scanner
displays “SCSI ID” on the upper
line of the LCD.
6
Select the wished SCSI ID by pressing the “
”or “
” button, and press “Enter” (the SCSI ID is set.)
7
Press “Exit” to return to the “Scanner Ready” screen if you don’t need to change the SCSI terminator.
NOTICE
If no other device is using the same SCSI ID, the scanner ID does not have to be changed.
NOTICE
The new ID does not take effect until the system power is turned On again.
8
Press “Next”
, then the
scanner displays “Terminator” on
the upper line of the LCD.
Select “On” or “Off” by pressing
or
, then press “Enter”.
NOTICE
The scanner includes a SCSI terminator that can be turned On and Off from the operator panel of the
scanner.
The factory default is “On.”
9
Press “Exit” to return to the “Scanner Ready” state.