Fujitsu Fi-4750c Operating Guide - Page 71

Contents of the Setup Mode, Switches the SCSI terminator On/Off.

Get Fujitsu Fi-4750c - Color Duplex Document Scanner 50ppm 90ipm Ccd/scsi PDF manuals and user guides
UPC - 097564303531
View all Fujitsu Fi-4750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Contents of the Setup Mode This section describes the contents of the setup mode. No Item Description Selectable parameters Default Specifies the double feed detection. Double 1 Double feed check feed is detected by checking the document No/Yes No length and/or paper thickness.** 2 Length check =No/10/15/20 mm Specifies the document length to enable double feed detection sets the document length. Tolerance: No/10/15/20mm No 3 IPC pre-setting Scanner automatically sets the recommended reading parameters. 3 sets of parameters are available when IPC-4D is not installed. Document: No 1: Sharpen 2: Darken Character 3: Copy Quality No 4 Resetting of abrasion counter Resets the abrasion counter. --- --- 5 Pick start time setting Specifies the time from document Insertion to the start of picking. User can select the most comfortable Pick start time for the job. Time: 0.2 to 29.8 sec 1.0 sec Specifies the time the scanner waits for the Time: 6 Time-out limit setting next document insertion after the last 27 values from document was scanned. 1 to 1999 sec 30 sec 7 ADF front offset setting* Specifies the horizontal and vertical offset of the front side image when using the ADF. Offset: H:-2 to +3 mm V:-2 to +3 mm Offset: H: 0 mm V: 0 mm 8 ADF back offset setting* Specifies the horizontal and vertical offset of the back side image when using the ADF. Offset: H:-2 to +3 mm V:-2 to +3 mm Offset: H: 0 mm V: 0 mm 9 Flatbed offset setting* Horizontal and vertical offset of the FB image is specified. Offset: H:-2 to +3 mm V:-2 to +3 mm Offset: H: 0 mm V: 0 mm 10 IPC status display Displays whether or not the image processing board (IPC-4D) is installed. --- --- 11 SCSI ID setting The SCSI ID is selectable. Note that the new setting is made valid after power is turned off and on again. SCSI ID: 0/1/2/3/4/5/6/7 5 12 SCSI terminator setting Switches the SCSI terminator On/Off. On/Off On 13 Low Power Mode setting Changes the default setting of the duration 5 min. for power save. to 60 min. 15 min. 7-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
7-2
Contents of the Setup Mode
This section describes the contents of the setup mode.
N
o
Item
Description
Selectable
parameters
Default
1
Double feed check
Specifies the double feed detection. Double
feed is detected by checking the document
length and/or paper thickness.**
No/Yes
No
2
Length check
=No/10/15/20 mm
Specifies the document length to enable
double feed detection sets the document
length.
Tolerance:
No/10/15/20mm
No
3
IPC pre-setting
Scanner automatically sets the
recommended reading parameters. 3 sets
of parameters are available when IPC-4D is
not installed.
Document:
No
1: Sharpen
2: Darken Character
3: Copy Quality
No
4
Resetting of
abrasion counter
Resets the abrasion counter.
---
---
5
Pick start time
setting
Specifies the time from document Insertion
to the start of picking. User can select the
most comfortable Pick start time for the job.
Time:
0.2 to 29.8 sec
1.0 sec
6
Time-out limit setting
Specifies the time the scanner waits for the
next document insertion after the last
document was scanned.
Time:
27 values from
1 to 1999 sec
30 sec
7
ADF front offset
setting*
Specifies the horizontal and vertical offset
of the front side image when using the ADF.
Offset:
H:-2 to +3 mm
V:-2 to +3 mm
Offset:
H: 0 mm
V: 0 mm
8
ADF back offset
setting*
Specifies the horizontal and vertical offset
of the back side image when using the
ADF.
Offset:
H:-2 to +3 mm
V:-2 to +3 mm
Offset:
H: 0 mm
V: 0 mm
9
Flatbed offset
setting*
Horizontal and vertical offset of the FB
image is specified.
Offset:
H:-2 to +3 mm
V:-2 to +3 mm
Offset:
H: 0 mm
V: 0 mm
10
IPC status display
Displays whether or not the image
processing board (IPC-4D) is installed.
---
---
11
SCSI ID setting
The SCSI ID is selectable.
Note that the
new setting is made valid after power is
turned off and on again.
SCSI ID:
0/1/2/3/4/5/6/7
5
12
SCSI terminator
setting
Switches the SCSI terminator On/Off.
On/Off
On
13
Low Power Mode
setting
Changes the default setting of the duration
for power save.
5 min.
to 60 min.
15 min.