Home » Ganz Security Manuals » Video Players » Ganz Security DR16HD » Manual Viewer

Ganz Security DR16HD DIGIMASTER H.264 Manual - Page 32

Display - Monitor

View all Ganz Security DR16HD manuals

Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

SYSTEM SETUP DISPLAY - MONITOR Click the MONITOR menu, then click on any field. Use the button to modify the value. SEQUENCE DWELL : The amount of time that each screen is displayed in a sequence. SPOT-OUT DWELL : The amount of time that each screen is displayed on each of the spot monitor outputs. DE-INTERLACE MODE : When recording any channels in D1 resolution (704 x 480), this may be set to ON, to prevent interlaced motion distortion during playback. ALARM POP-UP MODE : When enabled, an alarm input will cause the associated channel to display full screen. ALARM POP-UP DWELL : Determines the amount of time a full screen popup is displayed after an alarm input. If the alarm condition continues, the pop-up screen will be displayed constantly. MOTION POP-UP MODE : When enabled, motion detection will cause the associated channel to display full screen. MOTION POP-UP DWELL: Determines how long the full screen popup is displayed after motion detection. If motion continues, the popup screen is displayed constantly. To change any of these settings, highlight 'MONITOR' and press 'ENTER' to select. Use the CURSOR KEYS to navigate to the option required. Press ENTER to select the option (the cursor changes to orange) and use the CURSOR KEYS to change the setting. Press ENTER to save the setting, or press RETURN to cancel. NOTE: When display modes are changed, the DVR must be rebooted in order for changes to take effect. 32

Section	Page
Important Safety Instructions	11
17) CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.	11
ONLY DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.	11
Specifications & Organization	12
Specifications & Organization	13
Specifications & Organization	14
Specifications & Organization	15
Product Description	16
⑮ Channel Selection Buttons (1 ~ 8 / 16) : Select Channel or Input Password Digits	16
- ◀ ◀ / ◀ : Focus Adjust (Near / Far) or Reverse Play / Fast Rewind	16
- ▶ / ▶ ▶ : Iris Adjust (Open / Close) or Forward Play / Fast Forward	16
SYSTEM CONFIGURATION – Remote Controller	20
LIVE DISPLAY	22
SYSTEM SETUP	25
SYSTEM SETUP	27
SYSTEM SETUP	28
SYSTEM SETUP	29
SYSTEM SETUP	30
SYSTEM SETUP	31
SYSTEM SETUP	32
NOTE: When display modes are changed, the DVR must be rebooted in order for changes to take effect.	32
SYSTEM SETUP	33
Click the ‘SEQUENCE’ menu.	33
Click the ‘ADD’ button to add a new sequence.	33
SYSTEM SETUP	34
SYSTEM SETUP	35
Click on the ‘SPOT-OUT’ menu.	35
SYSTEM SETUP	36
From the ‘System Setup’ menu, click on the ‘SOUND’ menu.	36
SYSTEM SETUP	37
From the ‘System Setup’ menu, click the SYSTEM menu.	37
SYSTEM SETUP	38
SYSTEM SETUP	39
SYSTEM SETUP	40
SYSTEM SETUP	41
SYSTEM SETUP	42
SYSTEM SETUP	43
SYSTEM SETUP	44
Click on the ‘HDD EVENT’ menu, and choose any field.	44
Click on the ‘ALARM INPUT’ menu, and choose any field.	44
SYSTEM SETUP	45
Click on the ALARM OUTPUT menu, and click on a field.	45
Behavior settings	45
Action settings	45
NOTE: Remember to select ‘APPLY’ and press ‘ENTER’ to save all settings before exiting these menus.	45
SYSTEM SETUP	46
This menu will determine the behavior and actions that will trigger the internal buzzer.	46
Behavior settings	46
NOTE: Remember to select ‘APPLY’ and press ‘ENTER’ to save all settings before exiting these menus.	46
SYSTEM SETUP	47
EVENT / SENSOR - E-MAIL NOTIFICATION	47
Click on the EMAIL NOTIFICATION menu, and click on a field.	47
This menu will determine the behavior and actions that will send an e-mail notification to a remote user.	47
Behavior settings	47
FREQUENCY : Minimum period of time between sending e-mail notifications (max. 60 minutes).	47
NOTE: E-mail Notification settings must also be configured within the ‘MAIL’ and ‘USER MANAGEMENT’ menus.	47
SYSTEM SETUP	48
Click on the DISK MANAGEMENT menu.	48
NOTE: When a RECORD TIME LIMIT is set, the OVERWRITE option cannot be changed.	48
RECORD SETUP	49
From the Main Menu, click on the ‘RECORD’ menu.	49
To configure the recording behavior of the DVR, highlight ‘RECORD MENU’ and press ‘ENTER’.	49
RECORD SETUP	50
Click on the ‘CONTINUOUS / MOTION RECORDING’ menu.	50
SIZE / IPS / QUALITY	50
Click on the ‘SIZE / IPS / QUALITY’ tab.	50
To change ‘SIZE / IPS / QUALITY’ settings, highlight ‘CONTINUOUS / MOTION SETUP’ and press ‘ENTER’.	50
Ensure that ‘SIZE / IPS / QUALITY’ is highlighted in yellow, and press ‘ENTER’ again.	50
RECORD SETUP	51
SIZE / IPS / QUALITY (continued)	51
Click on the TIMELINE to select a block of time.	51
Click and drag on the TIMELINE to select a block of time.	51
RECORD SETUP	52
SIZE / IPS / QUALITY (continued)	52
Press ENTER. Recording settings for the selected time period are displayed.	52
NOTE: Remember that if the SCHEDULE MODE is set to WEEKLY, recording settings need to be changed for	52
As settings are adjusted, the ‘frames available’ at bottom left displays the number of available	52
images still remaining and must always be zero or higher.	52
If, while changing recording settings, this figure becomes negative, recording resolutions and/or	52
image rates must be lowered to increase the ‘frames available’ value to zero or above.	52
RECORD SETUP	53
SCHEDULE	53
Click on the ‘SCHEDULE’ menu.	53
RECORD SETUP	54
NOTE: Please refer to the instructions for the ‘CONTINUOUS / MOTION RECORDING’ menu for details on setting	54
up the ‘SIZE / IPS / QUALITY’ and ‘SCHEDULE’ tabs within the ‘ALARM RECORDING’ menu.	54
Alarm-activated recording can be used in conjunction with the ‘CONTINUOUS / MOTION RECORDING’ menu.	54
SEARCH	55
Click on the desired search date from the calendar.	55
SEARCH	56
Click and drag the time bar across the timeline.	56
Click the PLAY button on the bottom of the screen.	56
SEARCH	57
Turning counter-clockwise will reverse play up to 64x.	57
If the SHUTTLE WHEEL is released, playback is paused.	57
SEARCH	58
SEARCH	59
To exit playback mode and return to the search screen in	59
order to choose another time and date, press ‘RETURN’.	59
SEARCH	60
.	60
The event log search contains the following selectable entries:	60
ALARM: When this option is checked, all alarm input events are displayed for the chosen date range.	60
TIMER: When this option is checked, scheduled recording operations are displayed for the chosen date range.	60
MOTION: When this option is checked, all motion detection events are displayed for the chosen date range.	60
ARCHIVING	61
NOTE: To use a USB Memory Stick, it must be inserted into the DVR before entering the archiving menu.	61
ARCHIVING	62
NOTE: In case the selected data size for archiving exceeds the size of the CD / DVD / USB media being used,	62
the user may choose to continue the archive on additional pieces of media until complete.	62
Insert a new disc or drive after the first archive has completed, and click or press ‘CONTINUE’.	62
WEB CONNECTION SETUP	63
PRELIMINARY BEFORE CONNECTING	63
HOW TO CONNECT	63
WEB CONNECTION SETUP	64
The default User ID and Password are ‘ADMIN’ & ’1234’, respectively.	64
User will need to install the ActiveX control, click Run Add-on.	64
WEB CONNECTION SETUP	65
LIVE MODE	65
Icons and corresponding functions within LIVE mode:	65
- Select Live View Screen Division (1, 4, 8, 9, 16-channel modes)	65
- Select Live View Channel Manually.	65
WEB CONNECTION SETUP	66
WEB CONNECTION SETUP	67
SEARCH BY TIME	67
WEB CONNECTION SETUP	68
SEARCH BY EVENT	68
WEB CONNECTION SETUP	69
WEB CONNECTION SETUP	70
WEB CONNECTION SETUP	71
WEB CONNECTION SETUP	72
WEB CONNECTION SETUP	73
INFORMATION	73
- Displays the DVR Model and WEB Remote Software Version.	73
WATERMARK PROCESS	74
1. Open the archive data, and Run the file [bplayer.exe], which is included within the backup folder.	74
2. Click the [Open File] button and choose the backup file you wish to open and verify.	74
WATERMARK PROCESS	75
3. After selecting the file, you will be asked to confirm whether or not you would like to check the watermark.	75
4. Click the [Yes] button to verify the embedded watermark.	75
SMARTPHONE CONNECTION	76