Garmin 2620 Owners Manual - Page 72

Attaching the Vehicle Adapter to the StreetPilot 2620/2660, Use the AC - power cable

Get Garmin 2620 - StreetPilot Portable Automotive GPS Navigator PDF manuals and user guides
UPC - 753759045449
View all Garmin 2620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Appendix Vehicle Installation The vehicle adapter comes with an external speaker system that enables you to hear directions from your StreetPilot. Attaching the Vehicle Adapter to the StreetPilot 2620/2660 Your vehicle adapter is a 12/24 volt DC adapter with an external speaker system. This adapter is your StreetPilot's power source when you are in a vehicle (the StreetPilot does not use batteries). Use the AC adapter (included) when using the StreetPilot indoors. 1. Locate the power connector on the rear of the StreetPilot. The connector is "keyed" with a notch located towards the bottom of the plug. 2. Mate the power plug on the vehicle adapter to this connector by aligning the notches and sliding the plug into the connector until fully seated, as shown below. 3. Plug the cigarette lighter portion of the vehicle adapter into an available cigarette lighter receptacle in your vehicle. Use care when routing the adapter cable to ensure that it does not interfere with vehicle operation in any way. A 3AGC/3AG 1 amp fuse is located at the tip of the vehicle adapter Periodically, you may need to change the fuse that's located at the tip of the vehicle adapter. Simply unscrew the black, round end piece and remove/replace the fuse. 64 Attach the vehicle adapter to the back of your StreetPilot as shown above.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
Appendix
64
Attaching the Vehicle Adapter to the StreetPilot 2620/2660
Your vehicle adapter is a 12/24 volt DC adapter with an external speaker system. This adapter is your
StreetPilot’s power source when you are in a vehicle (the StreetPilot does not use batteries).
Use the AC
adapter (included) when using the StreetPilot indoors.
1.
Locate the power connector on the rear of the StreetPilot. The connector is “keyed” with a notch located
towards the bottom of the plug.
2.
Mate the power plug on the vehicle adapter to this connector by aligning the notches and sliding the plug
into the connector until fully seated, as shown below.
3. Plug the cigarette lighter portion of the vehicle adapter into an available cigarette lighter receptacle in
your vehicle. Use care when routing the adapter cable to ensure that it does not interfere with vehicle
operation in any way.
Vehicle Installation
The vehicle adapter comes with an external speaker
system that enables you to hear directions from your
StreetPilot.
Periodically, you may need to change the fuse
that’s located at the tip of the vehicle adapter.
Simply unscrew the black, round end piece and
remove/replace the fuse.
A 3AGC/3AG 1 amp
fuse is located at
the tip of the vehicle
adapter
Attach the vehicle adapter to the back of your
StreetPilot as shown above.