Home » Garmin Manuals » Marine Electronics » Garmin ECHOMAP UHD 72sv » Manual Viewer

Garmin ECHOMAP UHD 72sv Owners Manual - Page 34

Engaging the Autopilot, Steering Patterns, Reactor, Autopilot Remote Control, Connecting to

View all Garmin ECHOMAP UHD 72sv manuals

Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

1 From the autopilot screen, select MENU > Autopilot Setup > Preferred Sources 2 Select a source. If the selected heading source is unavailable, the autopilot screen does not display any data. Engaging the Autopilot When you engage the autopilot, the autopilot takes control of the helm and steers the boat to maintain your heading. From any screen, select Engage. Your intended heading shows in the center of the Autopilot screen. Steering Patterns WARNING You are responsible for the safe operation of your boat. Do not begin a pattern until you are certain that the water is clear of obstacles. The autopilot can steer the boat in preset patterns for fishing, and it can also perform other specialty maneuvers such as Uturns and Williamson turns. Following the U-Turn Pattern You can use the u-turn pattern to turn the boat around 180 degrees and maintain the new heading. 1 From the autopilot screen, select MENU > Pattern Steering > U-Turn. 2 Select Engage Port or Engage Starboard. Setting Up and Following the Circles Pattern You can use the circles pattern to steer the boat in a continuous circle, in a specified direction, and at a specified time interval. 1 From the autopilot screen, select MENU > Pattern Steering > Circles. 2 If necessary, select Time, and select a time for the autopilot to steer one complete circle. 3 Select Engage Port or Engage Starboard. Setting Up and Following the Zigzag Pattern You can use the zigzag pattern to steer the boat from port to starboard and back, over a specified time and angle, across your present heading. 1 From the autopilot screen, select MENU > Pattern Steering > Zigzag. 2 If necessary, select Amplitude, and select a degree. 3 If necessary, select Period, and select a length of time. 4 Select Engage Zigzag. Following the Williamson Turn Pattern You can use the Williamson turn pattern to steer the boat around with the intent of running alongside the location where the Williamson turn pattern was initiated. The Williamson turn pattern can be used in man overboard situations. 1 From the autopilot screen, select MENU > Pattern Steering > Williamson Turn. 2 Select Engage Port or Engage Starboard. You can wirelessly connect a Reactor autopilot remote control to the chartplotter to control the compatible Reactor autopilot system. For more information about using the remote, see the Reactor autopilot remote control instructions at garmin.com Pairing a Reactor Autopilot Remote Control With a Chartplotter 1 Select Settings > Communications > Wireless Devices > Autopilot Remote. 2 If necessary, select Enable. 3 Select New Connection. 4 On the remote control, select > Pair with MFD. The chartplotter beeps and shows a confirmation message. 5 On the chartplotter, select Yes to complete the pairing process. Changing the Functions of the Reactor Autopilot Remote Control Action Keys You can change the patterns or actions assigned to the Reactor autopilot remote control action keys. 1 Select Settings > Communications > Wireless Devices > Autopilot Remote > Button Actions. 2 Select an action key to change. 3 Select a pattern or action to assign to the action key. Force™ Trolling Motor Control WARNING Do not run the motor when the propeller is out of the water. Contact with the rotating propeller may result in severe injury. Do not use the motor in areas where you or other people in the water may come into contact with the rotating propeller. Always disconnect the motor from the battery before cleaning or servicing the propeller to avoid injury. You are responsible for the safe and prudent operation of your vessel. The autopilot is a tool that enhances your capability to operate your boat. It does not relieve you of the responsibility of safely operating your boat. Avoid navigational hazards and never leave the helm unattended. Learn to operate the autopilot on calm and hazard-free open water. Use caution when operating the autopilot near hazards in the water, such as docks, pilings, and other boats. CAUTION When using the autopilot features, be prepared for sudden stops, acceleration, and turns. When stowing or deploying the motor, be aware of the risk of entrapment or pinching from moving parts, which can result in injury. When stowing or deploying the motor, be aware of slick surfaces around the motor. Slipping when stowing or deploying the motor may result in injury. You can connect the Force trolling motor to the chartplotter to view and control the motor using the chartplotter. Reactor™ Autopilot Remote Control WARNING You are responsible for the safe and prudent operation of your vessel. The autopilot is a tool that enhances your capability to operate your boat. It does not relieve you of the responsibility of safely operating your boat. Avoid navigational hazards and never leave the helm unattended. Connecting to a Trolling Motor You can connect the chartplotter wirelessly to a compatible Garmin Force trolling motor on your boat to control the trolling motor from the chartplotter. 1 Turn on the chartplotter and the trolling motor. 2 Enable the Wi‑Fi network on the chartplotter (Setting Up the Wi‑Fi Wireless Network, page 38). 28 Force™ Trolling Motor Control

Section	Page
Table of Contents	3
Introduction	7
ECHOMAP UHD 60 Front View	7
Device Keys	7
ECHOMAP UHD 70/90 Front View	7
Device Keys	7
Assigning a Shortcut Key	7
Tips and Shortcuts	7
Downloading the Manuals from the Web	7
Garmin Support Center	7
Inserting Memory Cards	7
Acquiring GPS Satellite Signals	8
Selecting the GPS Source	8
Customizing the Chartplotter	8
Customizing the Home Screen	8
Customizing Pages	8
Creating a New Combination Page with the ECHOMAP UHD 70/90	8
Creating a New Combination Page with the ECHOMAP UHD 60	8
Setting the Vessel Type	8
Adjusting the Backlight	8
Adjusting the Color Mode	8
Changing the Background Image	8
ActiveCaptain App	9
ActiveCaptain Roles	9
Getting Started with the ActiveCaptain App	9
Enabling Smart Notifications	9
Updating Software with the ActiveCaptain App	9
Updating Charts with ActiveCaptain	9
Charts and 3D Chart Views	10
Navigation Chart and Fishing Chart	10
Zooming In and Out of the Chart	10
Panning the Chart with the Keys	10
Selecting an Item on the Map Using the Device Keys	10
Chart Symbols	10
Measuring a Distance on the Chart	10
Creating a Waypoint on the Chart	11
Navigating to a Point on the Chart	11
Viewing Location and Object Information on a Chart	11
Viewing Details about Navaids	11
Heading Line and Angle Markers	11
Setting the Heading Line and Angle Markers	11
Turning on Angle Markers	11
Premium Charts	11
Viewing Tide Station Information	12
Animated Tide and Current Indicators	12
Showing Tides and Current Indicators	12
Showing Satellite Imagery on the Navigation Chart	12
Viewing Aerial Photos of Landmarks	12
Automatic Identification System	12
AIS Targeting Symbols	12
Heading and Projected Course of Activated AIS Targets	13
Activating a Target for an AIS Vessel	13
Viewing Information about a Targeted AIS Vessel	13
Deactivating a Target for an AIS Vessel	13
Viewing a List of AIS Threats	13
Setting the Safe-Zone Collision Alarm	13
AIS Aids to Navigation	13
AIS Distress Signals	14
Navigating to a Distress Signal Transmission	14
AIS Distress Signal Device Targeting Symbols	14
Enabling AIS Transmission Test Alerts	14
Turning Off AIS Reception	14
Chart Menu	14
Chart Layers	14
Chart Layer Settings	14
My Vessel Layer Settings	15
Laylines Settings	15
User Data Layer Settings	15
Other Vessels Layer Settings	15
Water Layer Settings	15
Depth Range Shading	15
Fish Eye 3D Settings	16
Supported Maps	16
Garmin Quickdraw Contours Mapping	16
Mapping a Body of Water Using the Garmin Quickdraw Contours Feature	16
Adding a Label to a Garmin Quickdraw Contours Map	16
Garmin Quickdraw Community	16
Connecting to the Garmin Quickdraw Community with ActiveCaptain	16
Downloading Garmin Quickdraw Community Maps Using ActiveCaptain	16
Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using ActiveCaptain	17
Connecting to the Garmin Quickdraw Community with Garmin Connect	17
Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using Garmin Connect	17
Downloading Garmin Quickdraw Community Maps Using Garmin Connect	17
Garmin Quickdraw Contours Settings	17
Navigation with a Chartplotter	17
Basic Navigation Questions	18
Destinations	18
Searching for a Destination by Name	18
Selecting a Destination Using the Navigation Chart	18
Searching for a Marine Services Destination	18
Setting and Following a Direct Course Using Go To	18
Stopping Navigation	18
Waypoints	18
Marking Your Present Location as a Waypoint	18
Creating a Waypoint at a Different Location	18
Marking an MOB Location	19
Projecting a Waypoint	19
Viewing a List of all Waypoints	19
Editing a Saved Waypoint	19
Moving a Saved Waypoint	19
Browsing for and Navigating to a Saved Waypoint	19
Deleting a Waypoint or an MOB	19
Deleting All Waypoints	19
Routes	19
Creating and Navigating a Route From Your Present Location	19
Creating and Saving a Route	20
Viewing a List of Routes and Auto Guidance Paths	20
Editing a Saved Route	20
Browsing for and Navigating a Saved Route	20
Browsing for and Navigating Parallel to a Saved Route	20
Deleting a Saved Route	20
Deleting All Saved Routes	20
Auto Guidance	20
Setting and Following an Auto Guidance Path	20
Creating and Saving an Auto Guidance Path	21
Adjusting an Auto Guidance Path	21
Canceling an Auto Guidance Calculation in Progress	21
Setting a Timed Arrival	21
Auto Guidance Path Configurations	21
Adjusting the Distance from Shore	21
Tracks	22
Showing Tracks	22
Setting the Color of the Active Track	22
Saving the Active Track	22
Viewing a List of Saved Tracks	22
Editing a Saved Track	22
Saving a Track as a Route	22
Browsing for and Navigating a Recorded Track	22
Deleting a Saved Track	22
Deleting All Saved Tracks	22
Retracing the Active Track	22
Clearing the Active Track	22
Managing the Track Log Memory During Recording	22
Configuring the Recording Interval of the Track Log	22
Boundaries	22
Creating a Boundary	22
Converting a Route to a Boundary	23
Converting a Track to a Boundary	23
Editing a Boundary	23
Setting a Boundary Alarm	23
Deleting a Boundary	23
Deleting All Saved Waypoints, Routes, and Tracks	23
Sailing Features	23
Setting the Vessel Type	23
Sail Racing	23
Starting Line Guidance	23
Setting the Starting Line	23
Using the Starting Line Guidance	23
Using the Race Timer	23
Setting the Distance between the Bow and the GPS Antenna	23
Laylines Settings	24
Setting the Keel Offset	24
Sailboat Autopilot Operation	24
Wind Hold	24
Setting the Wind Hold Type	24
Engaging Wind Hold	24
Engaging Wind Hold from Heading Hold	24
Adjusting the Wind Hold Angle with the Autopilot	24
Tack and Gybe	25
Tacking and Gybing from Heading Hold	25
Tacking and Gybing from Wind Hold	25
Setting a Tack and Gybe Delay	25
Enabling the Gybe Inhibitor	25
Sonar Fishfinder	25
Stopping the Transmission of Sonar Signals	25
Changing the Sonar View	25
Traditional Sonar View	25
Split-Frequency Sonar View	25
Split-Zoom Sonar View	25
Garmin ClearVü Sonar View	25
SideVü Sonar View	26
SideVü Scanning Technology	26
Panoptix Sonar Views	26
LiveVü Down Sonar View	26
LiveVü Forward Sonar View	26
RealVü 3D Forward Sonar View	27
RealVü 3D Down Sonar View	27
RealVü 3D Historical Sonar View	27
FrontVü Sonar View	27
Panoptix LiveScope™‎ Sonar View	27
Flasher View	27
Flasher Page Shortcuts	28
Selecting the Transducer Type	28
Calibrating the Compass	28
Selecting a Sonar Source	28
Renaming a Sonar Source	28
Creating a Waypoint on the Sonar Screen	28
Pausing the Sonar Display	28
Measuring Distance on the Sonar Screen	28
Viewing Sonar History	29
Sonar Sharing	29
Adjusting the Level of Detail	29
Adjusting the Color Intensity	29
Sonar Recordings	29
Recording the Sonar Display	29
Stopping the Sonar Recording	29
Deleting a Sonar Recording	29
Playing Sonar Recordings	29
Traditional, Garmin ClearVü, and SideVü Sonar Setup	29
Setting the Zoom Level on the Sonar Screen	30
Setting the Scroll Speed	30
Adjusting the Range of the Depth or Width Scale	30
Sonar Appearance Settings	30
Sonar Alarms	30
Advanced Sonar Settings	30
Transducer Installation Settings	31
Sonar Frequencies	31
Selecting the Transducer Frequency	31
Creating a Frequency Preset	31
Turning On the A-Scope	31
Panoptix Sonar Setup	31
Adjusting the RealVü Viewing Angle and Zoom Level	31
Adjusting the RealVü Sweep Speed	31
LiveVü Forward and FrontVü Sonar Menu	31
Setting the LiveVü and FrontVü Transducer Transmit Angle	32
Setting the FrontVü Depth Alarm	32
LiveVü and FrontVü Appearance Settings	32
RealVü Appearance Settings	32
Panoptix Transducer Installation Settings	32
Setting the Bow Offset	33
Autopilot	33
Autopilot Screen	33
Adjusting the Step Steering Increment	33
Setting the Power Saver	33
Selecting the Preferred Heading Source	33
Engaging the Autopilot	34
Steering Patterns	34
Following the U-Turn Pattern	34
Setting Up and Following the Circles Pattern	34
Setting Up and Following the Zigzag Pattern	34
Following the Williamson Turn Pattern	34
Reactor™‎ Autopilot Remote Control	34
Pairing a Reactor Autopilot Remote Control With a Chartplotter	34
Changing the Functions of the Reactor Autopilot Remote Control Action Keys	34
Force™‎ Trolling Motor Control	34
Connecting to a Trolling Motor	34
Adding the Trolling Motor Controls to Screens	35
Trolling Motor Control Bar	35
Trolling Motor Settings	35
Assigning a Shortcut to the Trolling Motor Remote Control Shortcut Keys	35
Calibrating the Trolling Motor Compass	35
Setting the Bow Offset	35
Digital Selective Calling	36
Chartplotter and NMEA 0183 VHF Radio Functionality	36
Turning On DSC	36
DSC List	36
Viewing the DSC List	36
Adding a DSC Contact	36
Incoming Distress Calls	36
Navigating to a Vessel in Distress	36
Position Tracking	36
Viewing a Position Report	36
Navigating to a Tracked Vessel	36
Creating a Waypoint at the Position of a Tracked Vessel	36
Editing Information in a Position Report	36
Deleting a Position-Report Call	36
Viewing Vessel Trails on the Chart	36
Individual Routine Calls	36
Selecting a DSC Channel	36
Making an Individual Routine Call	37
Making an Individual Routine Call to an AIS Target	37
Gauges and Graphs	37
Viewing the Compass	37
Viewing Trip Gauges	37
Resetting Trip Gauges	37
Viewing Engine and Fuel Gauges	37
Selecting the Number of Engines Shown in Gauges	37
Customizing the Engines Shown in Gauges	37
Enabling Status Alarms for Engine Gauges	37
Enabling Some Engine Gauge Status Alarms	37
Setting the Fuel Alarm	37
Setting the Fuel Capacity of the Vessel	37
Synchronizing the Fuel Data with the Actual Vessel Fuel	37
Viewing the Wind Gauges	38
Configuring the Sailing Wind Gauge	38
Configuring the Speed Source	38
Configuring the Heading Source of the Wind Gauge	38
Customizing the Close-Hauled Wind Gauge	38
Digital Switching	38
Adding and Editing a Digital Switching Page	38
Tide, Current, and Celestial Information	38
Tide Station Information	38
Current Station Information	38
Celestial Information	38
Viewing Tide Station, Current Station, or Celestial Information for a Different Date	38
Viewing Information for a Different Tide or Current Station	38
Media Player	39
Opening the Media Player	39
Icons	39
Selecting the Media Source	39
Playing Music	39
Browsing for Music	39
Enabling Alphabetical Search	39
Setting a Song to Repeat	39
Setting All Songs to Repeat	39
Setting Songs to Shuffle	39
Adjusting the Volume	39
Enabling and Disabling Zones	39
Muting the Media Volume	39
VHF Radio	39
Scanning VHF Channels	39
Adjusting the VHF Squelch	39
Radio	39
Setting the Tuner Region	39
Changing the Radio Station	39
Changing the Tuning Mode	39
Presets	39
Saving a Station as a Preset	40
Removing a Preset	40
DAB Playback	40
Setting the DAB Tuner Region	40
Scanning for DAB Stations	40
Changing DAB Stations	40
Selecting a DAB Station from a List	40
Selecting a DAB Station from a Category	40
DAB Presets	40
Saving a DAB Station as a Preset	40
Selecting a DAB Preset from a List	40
Removing DAB Presets	40
SiriusXM Satellite Radio	40
Locating a SiriusXM Radio ID	40
Activating a SiriusXM Subscription	40
Customizing the Channel Guide	40
Saving a SiriusXM Channel to the Presets List	40
Unlocking SiriusXM Parental Controls	41
Setting Parental Controls on SiriusXM Radio Channels	41
Changing a Parental Passcode on a SiriusXM Radio	41
Restoring Default Parental Control Settings Values	41
Clearing All Locked Channels on a SiriusXM Radio	41
Setting the Device Name	41
Updating the Media Player Software	41
Device Configuration	41
Turning On the Chartplotter Automatically	41
System Settings	41
Display Settings	41
GPS Settings	41
Viewing the Event Log	42
Viewing System Software Information	42
Viewing E-label Regulatory and Compliance Information	42
My Vessel Settings	42
Setting the Keel Offset	42
Setting the Water Temperature Offset	42
Calibrating a Water Speed Device	43
Setting the Fuel Capacity of the Vessel	43
Synchronizing the Fuel Data with the Actual Vessel Fuel	43
Customizing Engine Gauge and Fuel Gauge Limits	43
Communications Settings	43
NMEA 0183	43
NMEA 0183 Settings	43
NMEA 2000 Settings	43
Naming Devices and Sensors on the Network	43
Wi‑Fi Network	44
Setting Up the Wi‑Fi Wireless Network	44
Connecting a Wireless Device to the Chartplotter	44
Changing the Wireless Channel	44
Setting Alarms	44
Navigation Alarms	44
System Alarms	44
Setting the Fuel Alarm	44
Units Settings	44
Navigation Settings	44
Other Vessel Settings	44
Restoring the Original Chartplotter Factory Settings	44
Sharing and Managing User Data	45
Connecting to a Garmin Device to Share User Data	45
User Data Sharing Cable Wiring Diagram	45
Selecting a File Type for Third-Party Waypoints and Routes	45
Copying User Data from a Memory Card	45
Copying User Data to a Memory Card	45
Copying Built-In Maps to a Memory Card	45
Copying Waypoints, Routes, and Tracks from HomePort to a Chartplotter	46
Backing Up Data to a Computer	46
Restoring Backup Data to a Chartplotter	46
Saving System Information to a Memory Card	46
Clearing Saved Data	46
Appendix	46
Registering Your Device with Garmin Express	46
Software Update	46
Loading the New Software on a Memory Card	46
Updating the Device Software	47
Cleaning the Screen	47
Screenshots	47
Capturing Screenshots	47
Copying Screenshots to a Computer	47
Troubleshooting	47
My device will not acquire GPS signals	47
My device will not turn on or keeps turning off	47
Changing the Fuse in the Power Cable	47
My sonar does not work	47
My device is not creating waypoints in the correct location	48
My device does not display the correct time	48
Specifications	48
All Models	48
6-Inch Models	48
7-Inch Models	48
9-Inch Models	48
Sonar Models Specifications	48
NMEA 0183 Information	48
NMEA 2000 PGN Information	49

Match case Limit results 1 per page

From the autopilot screen, select

Autopilot Setup

Preferred Sources

Select a source.

If the selected heading source is unavailable, the autopilot

screen does not display any data.

Engaging the Autopilot

When you engage the autopilot, the autopilot takes control of the

helm and steers the boat to maintain your heading.

From any screen, select

Engage

Your intended heading shows in the center of the Autopilot

screen.

Steering Patterns

WARNING

You are responsible for the safe operation of your boat. Do not

begin a pattern until you are certain that the water is clear of

obstacles.

The autopilot can steer the boat in preset patterns for fishing,

and it can also perform other specialty maneuvers such as U-

turns and Williamson turns.

Following the U-Turn Pattern

You can use the u-turn pattern to turn the boat around 180

degrees and maintain the new heading.

From the autopilot screen, select

Pattern Steering

U-Turn

Select

Engage Port

Engage Starboard

Setting Up and Following the Circles Pattern

You can use the circles pattern to steer the boat in a continuous

circle, in a specified direction, and at a specified time interval.

From the autopilot screen, select

Pattern Steering

Circles

If necessary, select

Time

, and select a time for the autopilot

to steer one complete circle.

Select

Engage Port

Engage Starboard

Setting Up and Following the Zigzag Pattern

You can use the zigzag pattern to steer the boat from port to

starboard and back, over a specified time and angle, across

your present heading.

From the autopilot screen, select

Pattern Steering

Zigzag

If necessary, select

Amplitude

, and select a degree.

If necessary, select

Period

, and select a length of time.

Select

Engage Zigzag

Following the Williamson Turn Pattern

You can use the Williamson turn pattern to steer the boat

around with the intent of running alongside the location where

the Williamson turn pattern was initiated. The Williamson turn

pattern can be used in man overboard situations.

From the autopilot screen, select

Pattern Steering

Williamson Turn

Select

Engage Port

Engage Starboard

Reactor

™

Autopilot Remote Control

WARNING

You are responsible for the safe and prudent operation of your

vessel. The autopilot is a tool that enhances your capability to

operate your boat. It does not relieve you of the responsibility of

safely operating your boat. Avoid navigational hazards and

never leave the helm unattended.

You can wirelessly connect a Reactor autopilot remote control to

the chartplotter to control the compatible Reactor autopilot

system.

For more information about using the remote, see the Reactor

autopilot remote control instructions at

garmin.com

Pairing a Reactor Autopilot Remote Control With a

Chartplotter

Select

Settings

Communications

Wireless Devices

Autopilot Remote

If necessary, select

Enable

Select

New Connection

On the remote control, select

Pair with MFD

The chartplotter beeps and shows a confirmation message.

On the chartplotter, select

Yes

to complete the pairing

process.

Changing the Functions of the Reactor Autopilot

Remote Control Action Keys

You can change the patterns or actions assigned to the Reactor

autopilot remote control action keys.

Select

Settings

Communications

Wireless Devices

Autopilot Remote

Button Actions

Select an action key to change.

Select a pattern or action to assign to the action key.

Force

™

Trolling Motor Control

WARNING

Do not run the motor when the propeller is out of the water.

Contact with the rotating propeller may result in severe injury.

Do not use the motor in areas where you or other people in the

water may come into contact with the rotating propeller.

Always disconnect the motor from the battery before cleaning or

servicing the propeller to avoid injury.

You are responsible for the safe and prudent operation of your

vessel. The autopilot is a tool that enhances your capability to

operate your boat. It does not relieve you of the responsibility of

safely operating your boat. Avoid navigational hazards and

never leave the helm unattended.

Learn to operate the autopilot on calm and hazard-free open

water.

Use caution when operating the autopilot near hazards in the

water, such as docks, pilings, and other boats.

CAUTION

When using the autopilot features, be prepared for sudden

stops, acceleration, and turns.

When stowing or deploying the motor, be aware of the risk of

entrapment or pinching from moving parts, which can result in

injury.

When stowing or deploying the motor, be aware of slick surfaces

around the motor. Slipping when stowing or deploying the motor

may result in injury.

You can connect the Force trolling motor to the chartplotter to

view and control the motor using the chartplotter.

Connecting to a Trolling Motor

You can connect the chartplotter wirelessly to a compatible

Garmin Force trolling motor on your boat to control the trolling

motor from the chartplotter.

Turn on the chartplotter and the trolling motor.

Enable the Wi

‑

Fi network on the chartplotter (

Setting Up the

‑

Fi Wireless Network

, page 38

Force

™

Trolling Motor Control