Garmin ECHOMAP UHD 72sv Owners Manual - Page 42
My Vessel Settings
View all Garmin ECHOMAP UHD 72sv manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 42 highlights
visibility, Galileo data can be used in combination with GPS to provide more accurate position information. Speed Filter: Averages the speed of your vessel over a short period of time for smoother speed values. Source: Allows you to select the preferred source for GPS data. Viewing the Event Log The event log shows a list of system events. Select Settings > System > System Information > Event Log. Viewing System Software Information You can view the software version, the basemap version, all supplemental map information (if applicable), the software version for an optional Garmin radar (if applicable), and the unit ID number. You may need this information to update the system software or to purchase additional map data information. You can view the software version, the basemap version, all supplemental map information (if applicable), and the unit ID number. You may need this information to update the system software or to purchase additional map data information. Select Settings > System > System Information > Software Information. Viewing E-label Regulatory and Compliance Information The label for this device is provided electronically. The e-label may provide regulatory information, such as identification numbers provided by the FCC or regional compliance markings, as well as applicable product and licensing information. Not available on all models. 1 Select Settings. 2 Select System. 3 Select Regulatory Information. Setting the Keel Offset You can enter a keel offset to compensate the water depth reading for the transducer installation location. This allows you to view the depth of the water below the keel or the true depth of the water, depending on your needs. If you want to know the water depth below the keel or the lowest point of your boat and the transducer is installed at the water line or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat. If you want to know the true water depth and the transducer is installed below the water line, measure the distance from the bottom of the transducer up to the water line. NOTE: This option is only available when you have valid depth data. 1 Measure the distance: • If the transducer is installed at the water line or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat. Enter this value as a positive number. • If the transducer is installed at the bottom of the keel and you want to know the true depth of the water, measure the distance from the transducer to the water line. Enter this value in as a negative number. My Vessel Settings NOTE: Some settings and options require additional charts or hardware. Select Settings > My Vessel. Keel Offset: Offsets the surface reading for the depth of a keel, making it possible to measure depth from the bottom of the keel instead of from the transducer location (Setting the Keel Offset, page 18). Calibrate Water Speed: Calibrates the speed-sensing transducer or sensor (Calibrating a Water Speed Device, page 37). Vessel Type: Enables some chartplotter features based on the boat type. Fuel Capacity: Sets the combined fuel capacity of all the fuel tanks on your vessel (Setting the Fuel Capacity of the Vessel, page 31). Fill Up All Tanks: Sets the tank levels to full (Synchronizing the Fuel Data with the Actual Vessel Fuel, page 31). Add Fuel to Boat: Allows you to enter the quantity of fuel you added to your tank, when you did not entirely fill up the tank (Synchronizing the Fuel Data with the Actual Vessel Fuel, page 31). Set Total Fuel Onboard: Sets the combined amount of fuel in all the fuel tanks on your vessel (Synchronizing the Fuel Data with the Actual Vessel Fuel, page 31). Set Gauge Limits: Sets the upper and lower limits of various gauges (Customizing Engine Gauge and Fuel Gauge Limits, page 37). Hull ID: Allows you to enter the Hull Identification Number (HIN).The HIN might be permanently affixed to the upper starboard side of the transom or outboard side. 2 Select Settings > My Vessel > Keel Offset. 3 Select if the transducer is installed at the water line, or select if the transducer is installed at the bottom of the keel. Setting the Water Temperature Offset Before you can set the water temperature offset, you must have a NMEA 0183 water-temperature sensor or a temperaturecapable transducer to measure water temperature. The temperature offset compensates for the temperature reading from a temperature sensor. 1 Measure the water temperature using the temperature sensor or temperature-capable transducer that is connected to the chartplotter. 2 Measure the water temperature using a different temperature sensor or a thermometer that is known to be accurate. 3 Subtract the water temperature measured in step 1 from the water temperature measured in step 2. This is the temperature offset. Enter this value in step 5 as a positive number if the sensor connected to the chartplotter measures the water temperature as being colder than it actually is. Enter this value in step 5 as a negative number if the sensor connected to the chartplotter measures the water temperature as being warmer than it actually is. 4 Select Settings > My Vessel > Temp. Offset. 36 Device Configuration