Gateway E-9232T Gateway E-9232T Server User Guide - Page 24

Preparing to install components, Selecting a place to work, Gathering the tools you need

Get Gateway E-9232T PDF manuals and user guides View all Gateway E-9232T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

CHAPTER 4: Installing Components Important You must open your server case to install components. If you are not comfortable with these procedures, get help from a more experienced computer user or computer service technician, or contact Gateway Customer Care. Preparing to install components Selecting a place to work Work on your server in an area that: • Is clean (avoid dusty areas) • Is a low-static environment (avoid carpeted areas) • Has a stable surface on which to set your server • Has enough room to place all of your server parts • Is near a grounded outlet so you can test your server after installation • Is near a telephone (in case you need help from Gateway Customer Care). The telephone must be directly connected to a telephone jack and cannot be connected to your server. Gathering the tools you need Some tools and supplies that you may need to work on your server are: • A notebook to take notes • A Phillips screwdriver • A small flat-blade screwdriver • Small containers to store various types of screws • A grounding wrist strap (available at most electronic stores) Preventing static electricity discharge Warning To avoid exposure to dangerous electrical voltages and moving parts, turn off your server and unplug the power cords and modem cable before opening the server case. The components inside your server are extremely sensitive to static electricity, also known as electrostatic discharge (ESD). Caution ESD can permanently damage electrostatic discharge-sensitive components in the server. Prevent ESD damage by following ESD guidelines every time you open the server case. Before working with server components, follow these guidelines: • Turn off the server, then unplug the power cords and all other cables. • Press the power button to drain any residual power from the server. Warning To prevent risk of electric shock, do not insert any object into the vent holes of the power supply module. • Wear a grounding wrist strap (available at most electronics stores) and attach it to a bare metal part of the server. You can also touch a bare metal surface on the back of the server with your finger. • Avoid static-causing surfaces such as carpeted floors, plastic, and packing foam. • Avoid working on the server when your work area is extremely humid. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
CHAPTER 4: Installing Components
18
Preparing to install components
Selecting a place to work
Work on your server in an area that:
•
Is clean (avoid dusty areas)
•
Is a low-static environment (avoid carpeted areas)
•
Has a stable surface on which to set your server
•
Has enough room to place all of your server parts
•
Is near a grounded outlet so you can test your server after installation
•
Is near a telephone (in case you need help from Gateway Customer Care). The telephone
must be directly connected to a telephone jack and cannot be connected to your server.
Gathering the tools you need
Some tools and supplies that you may need to work on your server are:
•
A notebook to take notes
•
A Phillips screwdriver
•
A small flat-blade screwdriver
•
Small containers to store various types of screws
•
A grounding wrist strap (available at most electronic stores)
Preventing static electricity discharge
The components inside your server are extremely sensitive to static electricity, also known as
electrostatic discharge
(ESD).
Before working with server components, follow these guidelines:
•
Turn off the server, then unplug the power cords and all other cables.
•
Press the power button to drain any residual power from the server.
•
Wear a grounding wrist strap (available at most electronics stores) and attach it to a bare
metal part of the server. You can also touch a bare metal surface on the back of the server
with your finger.
•
Avoid static-causing surfaces such as carpeted floors, plastic, and packing foam.
•
Avoid working on the server when your work area is extremely humid.
Important
You must open your server case to install components. If you are not comfortable
with these procedures, get help from a more experienced computer user or computer
service technician, or contact Gateway Customer Care.
Warning
To avoid exposure to dangerous electrical voltages and moving parts, turn off your
server and unplug the power cords and modem cable before opening the server case.
Caution
ESD can permanently damage electrostatic discharge-sensitive components in the
server. Prevent ESD damage by following ESD guidelines every time you open the server
case.
Warning
To prevent risk of electric shock, do not insert any object into the vent holes
of the power supply module.