Gateway E-9232T Gateway E-9232T Server User Guide - Page 49

Replacing the CMOS battery

Get Gateway E-9232T PDF manuals and user guides View all Gateway E-9232T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

www.gateway.com To replace a back fan: 1 Follow the instructions in "Preventing static electricity discharge" on page 18. 2 Follow the instructions in "Opening the server case" on page 19. 3 Unplug the fan cable from the fan connector on the system board. Fan cable Fan retention screw Fan retention screw 4 Unscrew the four fan retention screws holding the fan to the back of the chassis. 5 Pull the fan from the chassis, noting the orientation. Important Make sure that the new fan is oriented the same way (air flow) as the old fan. 6 Insert the new fan into the chassis, then replace the fan retention screws. 7 Plug the fan cable into the fan connector on the system board. 8 Follow the instructions in "Closing the server case" on page 24. Replacing the CMOS battery Warning There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer. Dispose of used batteries following the manufacturer's instructions. If the server clock does not keep time or the settings in the BIOS Setup utility are not saved when you turn off the server, replace the CMOS battery with an equivalent battery. To replace the battery: 1 Print the appendix for BIOS Settings in this guide. 2 Follow the instructions in "Opening the BIOS Setup utility" on page 48. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
www.gateway.com
43
To replace a back fan:
1
Follow the instructions in
“Preventing static electricity discharge” on page 18
.
2
Follow the instructions in
“Opening the server case” on page 19
.
3
Unplug the fan cable from the fan connector on the system board.
4
Unscrew the four fan retention screws holding the fan to the back of the chassis.
5
Pull the fan from the chassis, noting the orientation.
6
Insert the new fan into the chassis, then replace the fan retention screws.
7
Plug the fan cable into the fan connector on the system board.
8
Follow the instructions in
“Closing the server case” on page 24
.
Replacing the CMOS battery
If the server clock does not keep time or the settings in the BIOS Setup utility are not saved when
you turn off the server, replace the CMOS battery with an equivalent battery.
To replace the battery:
1
Print the appendix for
BIOS Settings
in this guide.
2
Follow the instructions in
“Opening the BIOS Setup utility” on page 48
.
Important
Make sure that the new fan is oriented the same way (air flow) as the old fan.
Warning
There is a danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type of battery recommended by the manufacturer. Dispose of used
batteries following the manufacturer’s instructions.
Fan cable
Fan retention screw
Fan retention screw