Gateway E-9232T Gateway E-9232T Server User Guide - Page 46

Replacing a power supply module

Get Gateway E-9232T PDF manuals and user guides View all Gateway E-9232T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

CHAPTER 4: Installing Components 8 When the processor is oriented correctly and in place, press it firmly into the socket, rotate the retention lever into place until it clicks. Caution The heatsink has Thermal Interface Material (TIM) located on the bottom of it. Use caution when you unpack the heat sink so you do not damage the TIM. If you are reusing the original heatsink, make sure that the TIM on the bottom of the heatsink is not damaged. If the TIM is damaged, you should remove the old TIM, then apply new TIM to the bottom of the heatsink. 9 Place the heatsink down onto the processor, then gently tighten the heatsink retaining screws to secure it into place. 10 Follow the instructions in "To close the server case:" on page 24. Replacing a power supply module Warning The power supply modules in this server contain no user-serviceable parts. Only a qualified computer technician should service the power supply modules. Your server comes with 3-wire AC power cords fitted with the correct plug style for your region. If this plug does not match the connector on your surge protector, UPS, or wall outlet, do not attempt to modify the plug in any way. Use a UPS or wall outlet that is appropriate for the supplied AC power cords. If your server uses the optional hot-swappable, redundant power supplies and one of the two power supplies fails, the other power supply module supports the server while you replace the failed module. You do not need to turn off the server or disconnect peripheral devices to replace a failed power supply module. To replace a power supply module: 1 If you only have one power supply module, turn off your server. 2 If you have two power supply modules, examine the LED indicators on the back of each power supply module to identify the failed module. The power supply module has failed if the orange (right) LED indicator is on. Power supply handle Power supply fault LED Power connector Power supply latch Power on LED 3 Unplug the power cord from the failed power supply module. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
CHAPTER 4: Installing Components
40
8
When the processor is oriented correctly and in place, press it firmly into the socket, rotate
the retention lever into place until it clicks.
9
Place the heatsink down onto the processor, then gently tighten the heatsink retaining
screws to secure it into place.
10
Follow the instructions in
“To close the server case:” on page 24
.
Replacing a power supply module
If your server uses the optional hot-swappable, redundant power supplies and one of the two
power supplies fails, the other power supply module supports the server while you replace the
failed module. You do not need to turn off the server or disconnect peripheral devices to replace
a failed power supply module.
To replace a power supply module:
1
If you only have one power supply module, turn off your server.
2
If you have two power supply modules, examine the LED indicators on the back of each
power supply module to identify the failed module. The power supply module has failed
if the orange (right) LED indicator is on.
3
Unplug the power cord from the failed power supply module.
Caution
The heatsink has Thermal Interface Material (TIM) located on the bottom of
it. Use caution when you unpack the heat sink so you do not damage the TIM. If
you are reusing the original heatsink, make sure that the TIM on the bottom of
the heatsink is not damaged. If the TIM is damaged, you should remove the old
TIM, then apply new TIM to the bottom of the heatsink.
Warning
The power supply modules in this server contain no user-serviceable parts. Only a
qualified computer technician should service the power supply modules.
Your server comes with 3-wire AC power cords fitted with the correct plug style for your
region. If this plug does not match the connector on your surge protector, UPS, or wall
outlet, do not attempt to modify the plug in any way. Use a UPS or wall outlet that is
appropriate for the supplied AC power cords.
Power supply fault LED
Power on LED
Power connector
Power supply latch
Power supply handle