GE PP9830SJSS Use and Care Manual - Page 15

INSTALLATION INSTRUCTIONS, Installation Instructions, PREPARATION

Page 15 highlights

INSTALLATION INSTRUCTIONS Installation Instructions PREPARATION TOOLS AND MATERIALS YOU WILL NEED • Cut resistant gloves • Saw • Flat-blade screwdriver • Electrician's pliers • Duct tape • Measuring tape or scale • Carpenter's square • 7/16" wrench or socket set • Drill and drill bit • Sheet metal screws • Junction box* • 3/4" flexible conduit* • Electrical wire per local code* • Wire nuts* • Ductwork *NOTE: Electrical installation kit JXCK89 may be ordered separately and includes all the parts necessary to connect the cooktop to typical rough-in wiring. CAUTION: FOR PERSONAL SAFETY, REMOVE HOUSE FUSE OR OPEN CIRCUIT BREAKER BEFORE PREPARING JUNCTION BOX. ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency, as listed in these Installation Instructions, and connected to an individual, properly grounded branch circuit, protected by a 40-amp circuit breaker or time delay fuses. All wire connections must be made in accordance with local codes and properly insulated. Check with your local utility for governing electrical codes and ordinances. In the absence of local electrical codes, the National Electrical Code, ANSI/ NFPA No. 70 - Latest Edition, governing electric range installations, must be followed. A copy of the National Electrical Code can be obtained by writing to: National Fire Protection Association Batterymarch Park Quincy, MA 02260 Effective January 1, 1996, the National Electrical Code requires that new, but not existing, construction utilize a four-conductor connection to an electric range. When installing an electric range in new construction, follow the instructions in NEW CONSTRUCTION AND FOURCONDUCTOR BRANCH CIRCUIT CONNECTION. You must use a three-wire, single-phase AC 208Y/120 Volt or 240/120 Volt, 60 Hertz electrical system with separate ground. If you connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be used. 30" COOKTOP (DIMENSIONS FOR REFERENCE ONLY) Unit shown fully assembled. 217ø8" (2115ø16"SS) 2923ø32" (2913ø16"SS) 22" 23ø16" (21ø4"SS) 201ø2" 283ø4" Unit must be vented to the outside! 49-80635-1 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56

49-80635-1
15
INSTALLATION INSTRUCTIONS
Installation Instructions
PREPARATION
30" COOKTOP (DIMENSIONS FOR REFERENCE ONLY)
Unit shown fully assembled.
Unit must be vented to the outside!
TOOLS AND MATERIALS YOU WILL NEED
• Cut resistant gloves
• Saw
• Flat-blade screwdriver
• Electrician’s pliers
• Duct tape
Measuring tape or scale
• Carpenter’s square
• 7/16” wrench or socket set
• Drill and drill bit
• Sheet metal screws
• Junction box*
• 3/4” flexible conduit*
• Electrical wire per local code*
• Wire nuts*
• Ductwork
*NOTE:
Electrical installation kit JXCK89 may be ordered
separately and includes all the parts necessary to connect
the cooktop to typical rough-in wiring.
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the proper voltage and
frequency, as listed in these Installation Instructions, and
connected to an individual, properly grounded branch circuit,
protected by a 40-amp circuit breaker or time delay fuses.
All wire connections must be made in accordance with local
codes and properly insulated. Check with your local utility for
governing electrical codes and ordinances. In the absence
of local electrical codes, the National Electrical Code, ANSI/
NFPA No. 70 – Latest Edition, governing electric range
installations, must be followed.
A copy of the National Electrical Code can be obtained by
writing to:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02260
Effective January 1, 1996, the National Electrical Code
requires that new, but not existing, construction utilize a
four-conductor connection to an electric range. When
installing an electric range in new construction, follow
the instructions in NEW CONSTRUCTION AND FOUR-
CONDUCTOR BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase AC 208Y/120 Volt
or 240/120 Volt, 60 Hertz electrical system with separate
ground. If you connect to aluminum wiring, properly
installed connectors approved for use with aluminum wiring
must be used.
CAUTION:
FOR PERSONAL SAFETY, REMOVE
HOUSE FUSE OR OPEN CIRCUIT BREAKER BEFORE
PREPARING JUNCTION BOX.
20
1
2
22”
28
3
4
2
3
16
(2
1
4
” SS)
21
7
8
(21
15
16
” SS)
29
23
32
(29
13
16
” SS)