Genie ChainLift 600 Owner's Manual - Page 16

FIG. 3-3, Insert wires, Power Head With Rear Cover Removed, FIG. 3-4, Mounting Wall Console., FIG. 3 - garage door opener manual

Get Genie ChainLift 600 PDF manuals and user guides View all Genie ChainLift 600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

3.Securely fasten wires. • Securely fasten wires to ceiling and wall using insulated staples provided. - Use insulated staples. - Staples should be snug only. Insulated • If rear cover is attached to power head, Staple remove it. • On power head: - Route wall console wires through wire guide on power head. - Split and strip ends of wire (Fig. 3-2 on previous page). - Insert wire into terminal holes and lightly press in the orange locking clips above each terminal hole. (You can use a pencil or small screwdriver to comfortably press in locking clips.) The white wire into #1 terminal hole and striped wire into the #2 terminal hole. - Confirm wire lock by lightly tugging on the wire. The wire should remain in the terminal hole. • Do NOT install rear cover yet. Locking Clips Terminal Holes 6 54 321 wire guide 6 54 3 21 +- PB Infrared Sensor (Power Head With Rear Cover Removed) FIG. 3-3 Insert wires. 4. Mounting. • Fasten wall console to wall with 2 screws (provided) (Fig. 3-4). • Remove protective backing from "Entrapment" warning label (Fig. 3-5). The "Entrapment" label is located in the center of this manual. - Stick label on wall near wall console. FIG. 3-4 Mounting Wall Console. Vacation Locking Switch - LOCK disables controls after 1 door is completely closed - UNLOCK allows controls to work normally Door Control "Open/Close" Button - Open and closes door from 2 inside garage 3 Independent Light Control - Controls door opener lights from inside garage - Energy-Saver shut-off turns OFF lights 3 minutes after door activation FIG. 3-5 DCheailAeNNItdfhmleewpcTovveeaeaeerrsIIPRrnyffMgsrrtlesodasoboefdpocllueeeeeeononnrektrnrttto1ecwoeifi/parccoaryseyi-llDoshhioiuspncntrpupoiiiocsellrlonenhiddnmfnolraronoeeioweintnuwoleblvsnadrojeereesvPejuasruolmctrdmaeisutleoncesrork,ef(eno.vgoydcmonvpenhrodeneoaix2tudcordrtnchesoxrtosousaoe4lrrprynarhwuondelatl:aaaoaaornlincclcdorpuhttirooefunoe(ltnaaarvnstonetdrnteos)lpjtueldrmueoraiastgolneishrtrttaihlfro.so5cotprtblfmoioae.ercuerebnntpoeetatgllrtavbrocoaoievnnrelsogafopl.ogeordnre)oeu.rosdero. or. ©1999 Mounting Entrapment warning label. 16 PN# 3642036534, 02/26/2010 REV. 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
PN# 3642036534, 02/26/2010
REV. 1
16
3.Securely fasten wires.
•
Securely fasten wires to ceiling and
wall using insulated staples provided.
– Use insulated staples.
– Staples should be snug only.
•
If rear cover is attached to power head,
remove it.
•
On power head:
– Route wall console wires through wire guide on
power head.
– Split and strip ends of wire
(Fig. 3-2 on
previous page)
.
– Insert wire into terminal holes and lightly press in
the orange locking clips above each terminal
hole. (You can use a pencil or small screwdriver
to comfortably press in locking clips.) The white
wire into #1 terminal hole and striped wire into
the #2 terminal hole.
– Confirm wire lock by lightly tugging on the wire.
The wire should remain in the terminal hole.
•
Do NOT install rear cover yet.
4. Mounting
.
•
Fasten wall console to wall with 2 screws
(provided)
(Fig. 3-4)
.
•
Remove protective backing from "Entrapment"
warning label
(Fig. 3-5)
. The "Entrapment" label
is located in the center of this manual.
– Stick label on wall near wall console.
Insulated
Staple
+–
P
B
Infrared Sensor
1
2
3
4
5
6
FIG. 3-3
Insert wires
.
(Power Head With Rear Cover Removed)
1
2
3
4
Terminal
Holes
Locking
Clips
5
6
wire guide
FIG. 3-4
Mounting Wall Console.
Child can be pinned under automatic garage door.
Death or serious injury can result.
•
Never let child walk or run under moving door.
.
•
Never let child use door opener controls.
•
Always keep moving door in sight.
•
If person is pinned, push control button or use
emergency release.
•
Test door opener monthly:
Refer to your owner s manual
Place 1/
-inch object (or 2x4 laid flat) on f oor
If door fails o reverse on contact adjust opener
If opener sti l fails o reverse door repair or replace opener
Do not remove or pa nt over this label
Mount wa l con rol out of chi ds reach (at least 5 feet above floor)
Place next to wall ontrol
©
1999
FIG. 3-5
Mounting Entrapment warning label
.
3
2
1
Independent Light Control
–
Controls door opener lights from inside garage
–
Energy-Saver shut-off turns OFF lights 3 minutes after
door activation
Vacation Locking Switch
– LOCK disables controls after
door is completely closed
– UNLOCK allows controls to
work normally
Door Control "Open/Close" Button
–
Open and closes door from
inside garage