Gigabyte B450 AORUS PRO WIFI User Manual - Page 40

Appendix, 3-1 Configuring a RAID Set

Get Gigabyte B450 AORUS PRO WIFI PDF manuals and user guides View all Gigabyte B450 AORUS PRO WIFI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Chapter 3 Appendix 3-1 Configuring a RAID Set RAID Levels Minimum Number of Hard Drives Array Capacity Fault Tolerance RAID 0 ≥2 Number of hard drives * Size of the smallest drive No RAID 1 2 Size of the smallest drive Yes RAID 10 4 (Number of hard drives/2) * Size of the smallest drive Yes Before you begin, please prepare the following items: •• At least two SATA hard drives or SSDs (Note 1) (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). (Note 2) •• Windows setup disk. •• Motherboard driver disk. •• A USB thumb drive. Configuring the Onboard SATA Controller A. Installing SATA hard drive(s) in your computer Install the hard drives/SSDs in the SATA/M.2 connectors on the motherboard. Then connect the power connectors from your power supply to the hard drives. B. Configuring SATA controller mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup. Steps: 1. Turn on your computer and press to enter BIOS Setup during the POST (Power-On Self-Test). Under Chipset, ensure Chipset SATA Port Enable is enabled. Set SATA Mode to RAID. Then save the settings and restart your computer. (If you want to use NVMe PCIe SSDs to configure RAID, make sure to set NVMe RAID mode to Enabled.) 2. If you want to configure UEFI RAID, follow the steps in "C-1." To enter the legacy RAID ROM, save the settings and exit BIOS Setup. Refer to "C-2" for more information. The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. C-1. UEFI RAID Configuration Steps: 1. In BIOS Setup, go to BIOS and set CSM Support to Disabled. Save the changes and exit BIOS Setup. 2. After the system reboot, enter BIOS Setup again. Then enter the Peripherals\RAIDXpert2 Configuration Utility sub-menu. 3. On the RAIDXpert2 Configuration Utility screen, press on Array Management to enter the Create Array screen. Then, select a RAID level. RAID levels supported include RAID 0(Stripe), RAID 1(Mirror), and RAID 10 (the selections available depend on the number of the hard drives being installed). Next, press on Select Physical Disks to enter the Select Physical Disks screen. 4. On the Select Physical Disks screen, select the hard drives to be included in the RAID array and set them to Enabled. Next, use the down arrow key to move to Apply Changes and press . Then return to the previous screen and set the Array Size, Array Size Unit, Read Cache Policy and Write Cache Policy. (Note 1) An M.2 PCIe SSD cannot be used to set up a RAID set either with an M.2 SATA SSD or a SATA hard drive. (Note 2) Refer to "1-7 Internal Connectors," for the installation notices for the M.2 and SATA connectors. - 40 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Chapter 3
Appendix
3-1
Configuring a RAID Set
Before you begin, please prepare the following items:
•
At least two SATA hard drives or SSDs
(Note 1)
(to ensure optimal performance, it is recommended that you
use two hard drives with identical model and capacity).
(Note 2)
•
Windows setup disk.
•
Motherboard driver disk.
•
A USB thumb drive.
Configuring the Onboard SATA Controller
A. Installing SATA hard drive(s) in your computer
Install the hard drives/SSDs in the SATA/M.2 connectors on the motherboard. Then connect the power connectors
from your power supply to the hard drives.
B. Configuring SATA controller mode in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup.
Steps:
1.
Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test).
Under
Chipset
, ensure
Chipset SATA Port Enable
is enabled. Set
SATA Mode
to
RAID
. Then save the
settings and restart your computer. (If you want to use NVMe PCIe SSDs to configure RAID, make sure to
set
NVMe RAID mode
to
Enabled
.)
2.
If you want to configure UEFI RAID, follow the steps in "C-1." To enter the legacy RAID ROM, save the
settings and exit BIOS Setup. Refer to "C-2" for more information.
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.
The actual BIOS Setup menu options you will see shall depend on the motherboard you have and
the BIOS version.
C-1. UEFI RAID Configuration
Steps:
1. In BIOS Setup, go to
BIOS
and set
CSM Support
to
Disabled
. Save the changes and exit BIOS Setup.
2. After the system reboot, enter BIOS Setup again. Then enter the
Peripherals\RAIDXpert2 Configuration
Utility
sub-menu.
3. On the
RAIDXpert2 Configuration Utility
screen, press <Enter> on
Array Management
to enter the
Create
Array
screen. Then, select a
RAID level
. RAID levels supported include RAID 0(Stripe), RAID 1(Mirror),
and RAID 10 (the selections available depend on the number of the hard drives being installed). Next, press
<Enter> on
Select Physical Disks
to enter the
Select Physical Disks
screen.
4. On the
Select Physical Disks
screen, select the hard drives to be included in the RAID array and set them
to
Enabled
. Next, use the down arrow key to move to
Apply Changes
and press <Enter>. Then return to
the previous screen and set the Array Size, Array Size Unit, Read Cache Policy and Write Cache Policy.
RAID Levels
RAID 0
RAID 1
RAID 10
Minimum Number of
Hard Drives
≥2
2
4
Array Capacity
Number of hard drives *
Size of the smallest drive
Size of the smallest drive
(Number of hard drives/2) *
Size of the smallest drive
Fault Tolerance
No
Yes
Yes
(Note 1) An M.2 PCIe SSD cannot be used to set up a RAID set either with an M.2 SATA SSD or a SATA hard drive.
(Note 2)
Refer to "1-7 Internal Connectors," for the installation notices for the M.2 and SATA connectors.
- 40 -