Gigabyte MSH61DK Manual - Page 41

SATA Configuration

Get Gigabyte MSH61DK PDF manuals and user guides View all Gigabyte MSH61DK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

2-2-3 SATA Configuration SATA Mode Select the on chip SATA type. IDE Mode: When set to IDE, the SATA controller disables its RAID and AHCI functions and runs in the IDE emulation mode. This is not allowed to access RAID setup utility. RAID Mode: When set to RAID, the SATA controllerenables both its RAID and AHCI functions. You will be allows access the RAID setup utility at boot time. ACHI Mode: When set to AHCI,the SATA controller enables its AHCI functionality. Then the RAID function is disabled and cannot be access the RAID setup utility at boot time. Options available: IDE/RAID/ACHI. Default setting is IDE Mode. Serial-ATA 0/1 Controllers Determine the on chip SATA controller 0/1 mode. Enhanced: SATA and PATA drives are auto-detected and placed inNative mode. Compatible: SATA and PATA drives are auto-detected and placed inLegacy mode. Default setting for Serial-ATA 0 controller is Compatible. Default setting for Serial-ATA 1 controller is Enhanced. SATA Port 0/1 The category identifies Serial ATA types of hard disk that are installed in the computer. System will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. Hard drive information should be labeled on the outside device casing. Enter the appropriate option based on this information. - 35 - BIOS Setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
- 35 -
BIOS Setup
2-2-3
SATA Configuration
SATA Mode
Select the on chip SATA type.
IDE Mode: When set to IDE, the SATA controller disables its RAID and AHCI functions and runs in the
IDE emulation mode. This is not allowed to access RAID setup utility.
RAID Mode: When set to RAID, the SATA controllerenables both its RAID and AHCI functions. You will
be allows access the RAID setup utility at boot time.
ACHI Mode: When set to AHCI,the SATA controller enables its AHCI functionality. Then the RAID func
-
tion is disabled and cannot be access the RAID setup utility at boot time.
Options available: IDE/RAID/ACHI. Default setting is
IDE Mode
.
Serial-ATA 0/1 Controllers
Determine the on chip SATA
controller 0/1 mode.
Enhanced: SATA and PATA drives are auto-detected and placed inNative mode.
Compatible: SATA and PATA drives are auto-detected and placed inLegacy mode.
Default setting for Serial-ATA 0 controller is
Compatible
.
Default setting for Serial-ATA 1 controller is
Enhanced
.
SATA Port 0/1
The category identifies Serial ATA
types of hard disk
that are installed in the computer.
System will automatically detect HDD type.
Note that the specifications of your drive must match with the drive table. The hard disk will not work
properly if you enter improper information for this category.
Hard drive information should be labeled on the outside device casing. Enter the appropriate option
based on this information.