Harman Kardon AVR 635 Owners Manual - Page 32
Operation
View all Harman Kardon AVR 635 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 32 highlights
OPERATION Basic Operation Once you have completed the initial setup and configuration of the AVR 635, it is simple to operate and enjoy. The following instructions will help you maximize the enjoyment of your new receiver: Turning the AVR 635 On or Off • When using the AVR 635 for the first time, you must press the Main Power Switch A to turn the unit on. This places the unit in a Standby mode, as indicated by the amber illumination surrounding the Standby/On Switch 1. Once the unit is in Standby, you may begin a listening session by pressing the Standby/On Switch 1 on the front panel, or the Power On Button b or AVR Selector e∫ on the remote. This will turn the unit on and return the AVR to the input source that was last used. The unit may also be turned on from Standby by pressing any of the Input Selector Buttons dXhç∂ on the remote or the Input Source Selector Button 7 on the front panel. Whenever the AVR is turned on, you will see all of the front-panel indicators light up for a few seconds. This is normal, and it is part of the unit's power-on self test procedure. NOTE: After pressing one of the Input Selector Buttons dXhç∂ to turn the unit on, press the AVR Selector e∫ to set the remote control to the AVR 635 functions. To turn the unit off at the end of a listening session, simply press the Standby/On Switch 1 on the front panel or the Power Off Button aå on the remote. Power will be shut off to any equipment plugged into the rear-panel Switched AC Accessory Outlet ⁄ and the illumination around the Standby/ On Switch 1 will turn amber. When the remote is used to turn the unit "off," it is actually placing the system in a Standby mode, as indicated by the amber lighting around the Standby/On Switch 1. • To program the AVR 635 for automatic turn-off, press the Sleep Button S on the remote. Each press of the button will decrease the time before shut-down in the following sequence: Once you have set the desired Sleep Time, the front panel display will automatically dim to half brightness and return. To check on the time remaining until the unit shuts off, press the Sleep Button S once. To cancel the Sleep function, press and hold the Sleep ButtonS until the information display returns to normal brightness; and the words SLEEP OFF will appear in the Lower Display Line $. When you will be away from home for an extended period of time, it is always a good idea to completely • The 6 CH DIRECT input should be used when the SBR and SBL inputs are NOT in use and turn the unit off with the front-panel Main Power Switch A. the input source device has its own internal bass management system. This input passes the input from the source directly through to the volume con- NOTE: All preset memories are lost if the unit is left turned off by using the Main Power Switch A for trol without any analog to digital conversion and it mutes the unused input jacks to prevent unwanted more than four weeks. 49 47 45nois4e3from interfering with system performance. 48 46 44 42 Source Selection 35 37 3•9The481 CH DIRECT input should be used • To select a source, press any of the Input Sele3c4tor 36 38whe4n0 an in3p7ut is41con4ne7cte5d1to all eight 8-Channel Buttons dXhç∂ on the remote.33 26 25Dir3e7ct Inp3u6ts 40 a4n6d w5h0en the input source 32 27 24dev3ic6e has3i5ts o3w9n in4te5rnal4b9ass management sys- • The input source may also be changed by press3in1g 28 23tem3.5This i3np4ut p3a8sse4s4the4in8put from the source the front-panel Input Source Selector Button370 . 29 22dire3c4tly thr3ou3gh to the43volume control without any Each press of the button will move the input sele2c9- 30 21ana3lo3g to d3i2gital conv4e2rsion and it mutes the tion through the list of available inputs. 28 31 20unu3s2ed inp3u1t jacks to prevent unwanted noise from interfering with system performance. • When a new input is selected, the AVR will automat- ically switch to the digital input (if selected), surround Volume and Tone Control mode, component video input, A/V Sync Delay and Night Mode configurations that were in effect the last time that input was used. If the LEVEL TRIM line on the CHANNEL ADJUST menu (Fig. 20) was set to INDEPENDENT, as shown on page 31, the settings for channel output levels will also change to the preset values. • The front-panel Video 4 Inputs N, Optical Digital 3 Input K or the Coaxial Digital 3 Input M may be used to connect a device such as a video game or camcorder to your home entertainment system on a temporary basis. • As the input source is changed, the new input name will appear momentarily as an on-screen display in the lower third of the video display. The input name will also appear in the Upper Display Line # and in the front-panel Input Indicators !. • Adjust the volum4e9to a47comf4o5rtable43level using the front-panel Volu4m8e C4o6ntro4l ) 4 o4r2remote Volume Up/Down Buttons r . 35 37 39 41 • To temporarily s3ile4nce3a6ll spe3a8ker o4u0tputs, p3r7ess t4h1e 47 51 Mute Button 33 26. Th2is5will3in7terrupt3th6e ou4t0- 46 50 p4u9t to a4ll7spea4k53er2s a4n3d27the h2e4adph3o6ne jack3,5but 3it 9 45 49 wiMn34ilU85pl nrToogtEr34aef67sfwse.icllWtf34laah49n33seyhn01ritenh44ceto21h22rsed89yisontnge-22mos32crirsdeuembn33ub54dtienisdgp,ltathhyae33ta34mwndoaryd3b8e 44 43 48 U3p4per 3D6ispla3y82L9ine40# 30, p2r3e17ss th34e31Mu4te73B2ut5to1ns 42 33 26ag2ai5n28to 3re73tu1rn to23n06orm34a2l0ope4ra6t3io1n.50 32 27 24 36 35 39 45 49 • Ttsh33ihgee01nfaurlonpnit22ta'stp89htaobnney22elp32C croenssto33rinor54gltshtemheareyTm33ob34oneteetaMV k3eo8nd.eoTu44Bht34euotfftitorhs4net 8on p2re9ss of3e0ithe2r 1butto3n3will sh3ow2 a messa4ge2in the o2n8-scre3en1dis2pl0ay a3nd2Lowe3r1Display Line $ with the current status of the tone controls. The sys- • When an audio only source is selected, the last video input used remains routed to the Video 1/Video 2 Video Outputs ‡· and Video Monitor Outputs ›. This permits simultaneous viewing and listening to different sources. tem default is TONE IN, which indicates that the bass and treble controls are active. Press the ⁄/¤ Navigation Button o on the remote or the ‹/› Button H on the front panel to change the setting to TONE OUT, which is "flat" response without the tone controls being active. • When a composite or S-video source is selected, the video signal for that input will be routed to the Video Monitor Output › and will be viewable on a TV monitor connected to the AVR 635. 49 47 45 43 • When the tone controls are active, the amount of bass and treble boost/cut may be adjusted by first pressing the Tone Mode Button on the front panel C or the remote V two or three times until the 6-Channel/8-Ch4a8nne4l6Dir4e4ct In4p2ut There are two inp3u5t ch3o7ices3a9vaila4b1le for use with sources such as3a4DVD36-Aud3i8o or4S0ACD 3p7laye4r 1that4a7re 51 connected to the383-Ch2a6nne2l5Dir3e7ct Inp3u6ts 40 . 46 50 Select the appro3pr2iate 2in7put2a4cco3rd6ing to3t5he w39ay y4o5ur 49 system and sourc3e1 equ2i8pme2n3t is 3c5onfigu3re4d: 38 44 48 30 29 22 34 33 43 29 30 21 33 32 42 28 31 20 32 31 desired setting (BASS MODE or TREBLE MODE) appears in the on-screen display and the Lower Display Line $. Next, use the ⁄/¤ Navigation Button o on the remote or the ‹/› Button on the front panel H to change the setting as desired. The unit will return to normal operation within 5 seconds after the setting is changed. 32 OPERATION