Hayward ColorLogic 4.0 LED Pool Light 120v/50 ft. Cable Plastic ColorLogic-Ins - Page 3

Introduction The Hayward® ColorLogic® LED (light-emitting diode) underwater lighting fixture you have purchased is designed to mount into Hayward fixture housings (niches) manufactured 1993 and later. Hayward light fixtures may fit into other niches, but the installation will not carry a UL approval. Hayward SP0524, SP0525, and W3SP0527/SP0527 Series ColorLogic LED pool lights are UL listed under file number E39338 and, to be approved, must be used with Hayward models SP0600, SP0607, SP0604C, or SP0609C fixture housings (niches). Hayward SP0532, SP0533 and W3SP0535/SP0535 Series ColorLogic LED spa lights are UL listed under file number E39338 and, to be approved, must be used with Hayward models SP0601, SP0608, SP0606C, or SP0610C fixture housings (niches). Installation of light and niche must be in accordance with Article 680 of the National Electric Code (NEC) and any applicable local codes. If non-metallic conduit is used, a #8 AWG grounding conductor must be run through the conduit and connected to the grounding connector on the inside of the niche. This connection must be encapsulated using a listed potting compound in accordance with NEC Article 680-20, such as 3M Scotch Cast Wet Niche Potting Compound No. 2135 (UL file E130394) or equivalent. The integral external connection on the niche should be connected to a #8 AWG bonding conductor also required by the NEC. Please refer to your niche instructions for details. Except when the fixture is installed in an area of the swimming pool or spa that is not used for swimming and the lens is adequately guarded to keep any person from contacting it, the fixture must be installed in or on a wall of the pool or spa, with the top of the lens not less than 18 inches (46 cm) below the normal water level of the pool or spa. Important Note When Installing Niches in Concrete/Gunite Pools SP0600, SP0601 and SP0608 Niches: A cardboard cover and 2 screws are provided with the niche to protect the niche and mounting screw holes. Leave these in place during construction to prevent intrusion of concrete which may damage the niche or screw threads. REMOVE and discard both the screws and the protective cardboard cover when ready to install the light fixture. SP0604C, SP0606C, SP0609C, and SP0610C Niches: A plastic cover is provided with the niche to protect the niche and mounting screw holes. Leave the cover in place during construction to prevent intrusion of concrete which may damage the niche or screw threads. Before applying plaster, the outer edge of the cover may be torn off to allow plastering up to the edge of the niche. REMOVE and discard the plastic cover when ready to install the light fixture. If the light fixture is installed in the niche before pool or spa construction, the plastic cover may be reversed and taped to the edge of the light's face plate to protect the light from concrete during construction. GIVE THESE INSTRUCTIONS TO POOL/SPA OWNER AFTER INSTALLATION POOL PISCINE PISCONA SPA JACUZZI Model # Modèle No Modelo No. SP0524(S)LED Voltage Tension Voltaje (VAC) 12 Wattage Puissance Vataje (W) Wire Size Taille de câble Tamaño del cable (AWG) For Use With Niches À utiliser avec des enfoncements Para uso con nichos For Country Pays Para el país 50 12 SP0600U, SP0607U, SP0604C, SP0609C United States SP0525(S)LED 120 50 SP0527(S)LED 120 95 W3SP0527(S)LED 120 95 16 SP0600U, SP0607U, SP0604C, SP0609C United States SP0532(S)LED 12 25 16 SP0601U, SP0606C, SP0610C, SP0608U United States SP0533(S)LED 120 25 SP0535(S)LED 120 40 W3SP0535(S)LED 120 40 16 SP0601U, SP0606C, SP0610C, SP0608U United States SP0524CLED 12 50 14 SP0600U, SP0607U, SP0604C, SP0609C Canada SP0525CLED 120 50 14 SP0527CLED 120 95 SP0604C, SP0609C Canada SP0532CLED 12 25 14 SP0601U, SP0606C, SP0610C, SP0608U Canada SP0533CLED 120 25 14 SP0606C, SP0610C, SP0608U Canada SP0535CLED 120 40 2 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS POOL PISCINE PISCONA SPA JACUZZI