HealthRider H40v Vibration English Manual - Page 15

Troubleshooting

Get HealthRider H40v Vibration PDF manuals and user guides View all HealthRider H40v Vibration manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

TROUBLESHOOTING Inspect all parts of the vibration platform regularly. Replace any worn parts immediately. Outer surfaces of the vibration platform can be cleaned with a damp cloth and a mild, non-abrasive detergent; do not use solvents to clean the vibration platform. Most vibration platform problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the telephone number on the front cover of this manual. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is fully plugged into the receptacle on the base of the vibration platform. Next, make sure that the power cord is plugged into an appropriate outlet (see page 11). IMPORTANT: The vibration platform is not compatible with GFCI-equipped outlets. b. Check the on/off switch located on the vibration plat- form base near the power cord. Make sure that the b on/off switch is in the on position. Off On c. If the power cord is plugged in and the on/off switch is in the on position, the fuse may need to be replaced. To replace the fuse, first switch the on/off switch to the off position and unplug the power cord. Using a Phillips screwdriver, remove the fuse holder located above the on/off switch. Remove the fuse from the fuse holder. Insert a new fuse into the fuse holder. Note: The correct type of fuse to use is listed on the fuse holder. Replace the fuse holder, plug in the power cord, switch the on/off switch to the on position, and run the vibration platform to check for correct operation. d. If the vibration platform still will not run, please see the back cover of this manual. PROBLEM: The power turns off during use SOLUTION: a. Check the on/off switch (see the drawing on page 11). Make sure that the on/off switch is in the on position. b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it in. c. If the power cord is plugged in and the on/off switch is in the on position, the fuse may need to be replaced. See step c. above to replace the fuse. d. If the vibration platform still will not run, please see the back cover of this manual. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
15
TROUBLESHOOTING
Inspect all parts of the vibration platform regularly. Replace any worn parts immediately. Outer surfaces of the vibra-
tion platform can be cleaned with a damp cloth and a mild, non-abrasive detergent;
do not use solvents to clean
the vibration platform.
Most vibration platform problems can be solved by following the simple steps below. Find the symptom
that applies, and follow the steps listed. If further assistance is needed, see the telephone number on
the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION:
a. Make sure that the power cord is fully plugged into the receptacle on the base of the vibration
platform. Next, make sure that the power cord is plugged into an appropriate outlet (see page
11).
IMPORTANT: The vibration platform is not compatible with GFCI-equipped outlets.
b. Check the on/off switch located on the vibration plat-
form base near the power cord. Make sure that the
on/off switch is in the on position.
c. If the power cord is plugged in and the on/off switch is in the on position, the fuse may need to
be replaced.
To replace the fuse, first switch the on/off switch to the off position and unplug the power cord.
Using a Phillips screwdriver, remove the fuse holder located above the on/off switch. Remove
the fuse from the fuse holder.
Insert a new fuse into the fuse holder. Note: The correct type of fuse to use is listed on the fuse
holder.
Replace the fuse holder, plug in the power cord, switch the on/off switch to the on position, and
run the vibration platform to check for correct operation.
d. If the vibration platform still will not run, please see the back cover of this manual.
PROBLEM: The power turns off during use
SOLUTION:
a. Check the on/off switch (see the drawing on page 11). Make sure that the on/off switch is in the
on position.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it in.
c. If the power cord is plugged in and the on/off switch is in the on position, the fuse may need to
be replaced. See step c. above to replace the fuse.
d. If the vibration platform still will not run, please see the back cover of this manual.
Off
On
b