HealthRider Hotel Fitness It9800 Treadmill English Manual - Page 35

cannot be adjusted even though the console

Get HealthRider Hotel Fitness It9800 Treadmill PDF manuals and user guides View all HealthRider Hotel Fitness It9800 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

SYMPTOM: The walking belt is off-center or slips when walked on a. If the walking belt has shifted to the right: Remove the key and unplug the power cord. Using a 7/32" hex key, turn the roller adjustment screws in the directions shown, 1/4 of a turn each. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and use the incline trainer for a few minutes. Repeat until the walking belt is centered. a Right belt should just touch the walking platform. Make sure to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the incline trainer for a few minutes. Repeat until the walking belt is properly tightened. Note: As you tighten the roller adjustment screws, the front roller will move. If the front roller stops moving, do not further tighten the roller adjustment screws; please see the back cover of this manual. c b. If the walking belt has shifted to the left: Remove the key and unplug the power cord. Using a 7/32" hex key, turn the roller adjustment screws in the directions shown, 1/4 of a turn each. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and use the incline trainer for a few minutes. Repeat until the walking belt is centered. b Left c. If the walking belt slips when walked on: Remove the key and unplug the power cord. Using a 7/32" hex key, turn both roller adjustment screws clockwise 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 2.5 to 5 cm (1 to 2 in.) off the walking platform. The center of the walking SYMPTOM: The walking belt stops or the incline cannot be adjusted even though the console remains lit a. This indicates that a controller error may have occurred. To correct the problem, turn the power switch off, wait for 5 seconds, and then turn the power switch back on. SYMPTOM: The incline system does not function properly or the incline system does not appear to be at the incline level shown in the display a. Calibrate the incline system (see step 4 on page 27). b. If the incline system still does not function properly, please see the back cover of this manual. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
35
SYMPTOM: The walking belt is off-center or slips
when walked on
a.
If the walking belt has shifted to the right:
Remove the key and unplug the power cord.
Using a 7/32" hex key, turn the roller adjustment
screws in the directions shown, 1/4 of a turn each.
Be careful not to overtighten the walking belt.
Then, plug in the power cord, insert the key, and
use the incline trainer for a few minutes. Repeat
until the walking belt is centered.
b.
If the walking belt has shifted to the left:
Remove the key and unplug the power cord.
Using a 7/32" hex key, turn the roller adjustment
screws in the directions shown, 1/4 of a turn each.
Be careful not to overtighten the walking belt.
Then, plug in the power cord, insert the key, and
use the incline trainer for a few minutes. Repeat
until the walking belt is centered.
c.
If the walking belt slips when walked on:
Remove the key and unplug the power cord.
Using a 7/32" hex key, turn both roller adjustment
screws clockwise 1/4 of a turn. When the walking
belt is properly tightened, you should be able to lift
each side of the walking belt 2.5 to 5 cm (1 to 2 in.)
off the walking platform. The center of the walking
belt should just touch the walking platform.
Make
sure to keep the walking belt centered.
Then,
plug in the power cord, insert the key, and run the
incline trainer for a few minutes. Repeat until the
walking belt is properly tightened. Note: As you
tighten the roller adjustment screws, the front roller
will move.
If the front roller stops moving, do not
further tighten the roller adjustment screws;
please see the back cover of this manual.
SYMPTOM: The walking belt stops or the incline
cannot be adjusted even though the console
remains lit
a.
This indicates that a controller error may have
occurred. To correct the problem, turn the power
switch off, wait for 5 seconds, and then turn the
power switch back on.
SYMPTOM: The incline system does not function
properly or the incline system does not appear to
be at the incline level shown in the display
a.
Calibrate the incline system (see step 4 on page
27).
b.
If the incline system still does not function properly,
please see the back cover of this manual.
a
Right
b
Left
c