HP 2000-2d20ca HP 2000 Notebook PC and Compaq CQ58 Notebook PC - Maintenance a - Page 48

Display subcomponents (bezel, webcam, panel), Remove the two Mylar screw covers

Get HP 2000-2d20ca PDF manuals and user guides View all HP 2000-2d20ca manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Display subcomponents (bezel, webcam, panel) This section describes removing display subcomponents that do not require that you remove the entire display assembly from the computer. You can remove the display bezel, webcam/microphone module, and display panel while the display assembly is still attached to the computer. To remove the remaining display subcomponents, including the hinge covers, hinges, cable, antennas, and enclosure, you must remove the entire display assembly from the computer. See Display assembly on page 75 for more information about removing the display assembly in its entirety. Description Display bezel for use on HP models (includes Mylar screw covers) Display bezel for use on Compaq models (includes Mylar screw covers) Raw display panel, 39.6-cm (15.6-inch), HD, LED, BrightView HP webcam/microphone module, HD HP VGA webcam/microphone module Spare part number 689675-001 689676-001 689690-001 703461-001 685112-001 Before removing the display bezel, webcam/microphone module, and display panel while the display assembly is still attached to the computer, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 39). To remove the display bezel, webcam/microphone module, and display panel while the display assembly is still attached to the computer: 1. Position the computer right-side up with the front toward you, and then open it. 2. Remove the two Mylar screw covers (1) and the two Phillips PM2.5×4.0 screws (2) that secure the display bezel to the display assembly. The Mylar screw covers are included with the display bezel spare part kit. 3. Flex the inside edges of the top edge, the left and right sides, and the bottom edge of the display bezel until the bezel disengages from the display enclosure. 40 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
Display subcomponents (bezel, webcam, panel)
This section describes removing display subcomponents that do not require that you remove the entire
display assembly from the computer. You can remove the display bezel, webcam/microphone module, and
display panel while the display assembly is still attached to the computer.
To remove the remaining display subcomponents, including the hinge covers, hinges, cable, antennas, and
enclosure, you must remove the entire display assembly from the computer. See
Display assembly
on page
75
for more information about removing the display assembly in its entirety.
Description
Spare part number
Display bezel for use on HP models (includes Mylar screw covers)
689675-001
Display bezel for use on Compaq models (includes Mylar screw covers)
689676-001
Raw display panel, 39.6-cm (15.6-inch), HD, LED, BrightView
689690-001
HP webcam/microphone module, HD
703461-001
HP VGA webcam/microphone module
685112-001
Before removing the display bezel, webcam/microphone module, and display panel while the display
assembly is still attached to the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see
Battery
on page
39
).
To remove the display bezel, webcam/microphone module, and display panel while the display assembly is
still attached to the computer:
1.
Position the computer right-side up with the front toward you, and then open it.
2.
Remove the two Mylar screw covers
(1)
and the two Phillips PM2.5×4.0 screws
(2)
that secure the
display bezel to the display assembly. The Mylar screw covers are included with the display bezel spare
part kit.
3.
Flex the inside edges of the top edge, the left and right sides, and the bottom edge of the display bezel
until the bezel disengages from the display enclosure.
40
Chapter 4
Removal and replacement procedures
ENWW