HP 2000-2d20ca HP 2000 Notebook PC and Compaq CQ58 Notebook PC - Maintenance a - Page 94

system board., To remove the system board

Get HP 2000-2d20ca PDF manuals and user guides View all HP 2000-2d20ca manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

NOTE: When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● Memory module (see Memory module on page 51) ● RTC battery (see RTC battery on page 55) ● Fan/heat sink assembly (see Fan/heat sink assembly on page 90) ● Processor (Intel only; see Processor on page 96) NOTE: AMD processors come soldered to the system board and cannot be removed or replaced. To remove the system board: 1. Close the computer, turn it upside down, and then disconnect the optical drive connector cable from the system board. 2. Position the computer upright, and then remove the three Phillips PM2.5×4.0 screws (1) that secure the system board to the base enclosure. 86 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
NOTE:
When replacing the system board, be sure that the following components are removed from the
defective system board and installed on the replacement system board:
●
Memory module (see
Memory module
on page
51
)
●
RTC battery (see
RTC battery
on page
55
)
●
Fan/heat sink assembly (see
Fan/heat sink assembly
on page
90
)
●
Processor (Intel only; see
Processor
on page
96
)
NOTE:
AMD processors come soldered to the system board and cannot be removed or replaced.
To remove the system board:
1.
Close the computer, turn it upside down, and then disconnect the optical drive connector cable from the
system board.
2.
Position the computer upright, and then remove the three Phillips PM2.5×4.0 screws
(1)
that secure the
system board to the base enclosure.
86
Chapter 4
Removal and replacement procedures
ENWW