HP 220mx HP SureStore 220mx Optical Jukebox User's Guide - Page 67

Table 3 -3, Troubleshooting

Get HP 220mx PDF manuals and user guides View all HP 220mx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Operating the Jukebox Table 3 -3 Operating the Jukebox Troubleshooting Troubleshooting Problem What to do Jukebox won't power on • Check that the drive activity indicator light on the control panel is ON ("4" on Figure 3-1) while you see TESTING in the display. • If light is not ON, make sure the standby/on switch on the rear panel is in the ON position and that the jukebox is plugged in. • Is the power cord good? • Is the power outlet operating? • If steps above are unsuccessful, go to "HP Services and Support" at www.hp.com. Poweron selftest failed Ensure that shipping screw is removed. Ensure that the shipping bracket (in the mailslot) is removed. Power cycle the jukebox.* If jukebox continues to fail poweron selftest, press ENTER and record the error codes. Call your service representative. Power to the jukebox failed while a disk was in the drive and did not return to READY after the power came back on Power cycle the jukebox.* If the poweron test is unsuccessful, place the standby/on switch to STANDBY. Do not move the jukebox! Moving the jukebox when there is a disk cartridge inside the drive risks damaging the drive. Call your service representative. * Before turning power to STANDBY, ensure that the SCSI bus is inactive and will remain inactive while you are troubleshooting. Going to STANDBY in this jukebox while the SCSI bus is active can cause data loss and/or SCSI bus problems. Chapter 3 3-29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Chapter 3
3-29
Operating the Jukebox
Troubleshooting
Operating the Jukebox
Table 3 -3
Troubleshooting
Problem
What to do
Jukebox won
’
t
power on
•
Check that the drive activity indicator light on
the control panel is ON (
“
4
”
on Figure 3-1)
while you see
TESTING
in the display.
•
If light is not ON, make sure the standby/on
switch on the rear panel is in the ON position
and that the jukebox is plugged in.
•
Is the power cord good?
•
Is the power outlet operating?
•
If steps above are unsuccessful, go to
“HP
Services and Support”
at
www.hp.com
.
Poweron selftest
failed
Ensure that shipping screw is removed.
Ensure that the shipping bracket (in the mailslot)
is removed.
Power cycle the jukebox.*
If jukebox continues to fail poweron selftest, press
ENTER
and record the error codes. Call your
service representative.
Power to the
jukebox failed
while a disk was
in the drive and
did not return to
READY
after the
power came back
on
Power cycle the jukebox.*
If the poweron test is unsuccessful, place the
standby/on switch to STANDBY.
Do not move the
jukebox!
Moving the jukebox when there is a disk
cartridge inside the drive risks damaging the
drive. Call your service representative.
* Before turning power to STANDBY, ensure that the SCSI bus is
inactive and will remain inactive while you are troubleshooting. Going
to STANDBY in this jukebox while the SCSI bus is active can cause
data loss and/or SCSI bus problems.