HP A7518B HP StorageWorks SDLT Tape Drive Getting Started Guide - internal mod - Page 19

Step 4: Attach mounting hardware, HP ProLiant servers, Other servers

Get HP A7518B - StorageWorks SDLT 600 Tape Drive PDF manuals and user guides
UPC - 882780125599
View all HP A7518B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Step 4: Attach mounting hardware If your server requires special rails or other hardware to install the tape drive, mount them on the tape drive in this step. If your server does not require special mounting hardware, proceed to "Step 5: Install the drive" on page 17 now. For example, HP AlphaServers do not require special mounting hardware. HP ProLiant servers Different models of server require different mounting methods. The server may also incorporate a locking mechanism to hold the tape drive in place. See "Step 7: Secure the drive" on page 21. Please check your HP ProLiant server documentation to ascertain the correct method of mounting, and to check whether mounting hardware is provided with the server. Mounting rails Some HP ProLiant servers, such as ML530 and ML570, require mounting rails. These may be metal or plastic rails attached to the server's drive bay filler panel. 1 Use a regular Phillips screwdriver to attach the appropriate rails. Use the M3 screws provided with the tape drive. For ML530 servers position the screws in the right-hand holes on the tape drive (holes 1 and 3), as shown in Figure 5a. For ML570 servers position the screws in the left-hand holes on the tape drive (holes 2 and 4), as shown in Figure 5b. Ensure you do use the M3 screws provided - the rails may be attached to the filler panel by screws of a different thread/size type and these should not be used. If in doubt, refer to your HP ProLiant server documentation. Mounting screws Other HP ProLiant server models, such as ML350 and ML370, only require the use of special locating screws with no mounting rail. 1 Use a T8 Torx screwdriver to attach the appropriate screws. You may need to purchase the M3 screws separately. Position the screws in the right-hand holes on the tape drive (holes 1 and 3), as shown in Figure 5c. • HP ProLiant ML350: Use M3 mounting screws. These have a thicker head than the standard M3 screws. • HP ProLiant ML370: Use M3 offset mounting screws. These have a thick offset piece and a thicker head than the standard M3 screws. Other servers 1 Attach the appropriate mounting hardware. Refer to the manufacturer's documentation for instructions. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
15
Step 4: Attach mounting hardware
If your server requires special rails or other hardware to install the tape drive, mount them on
the tape drive in this step.
If your server does not require special mounting hardware, proceed
to “Step 5: Install the drive” on page 17 now. For example, HP AlphaServers do not require
special mounting hardware.
HP ProLiant servers
Different models of server require different mounting methods. The server may also
incorporate a locking mechanism to hold the tape drive in place. See “Step 7: Secure the
drive” on page 21.
Please check your HP ProLiant server documentation to ascertain the correct method of
mounting, and to check whether mounting hardware is provided with the server.
Mounting rails
Some HP ProLiant servers, such as ML530 and ML570, require mounting rails. These may be
metal or plastic rails attached to the server's drive bay filler panel.
1
Use a regular Phillips screwdriver to attach the appropriate rails. Use the M3 screws provided
with the tape drive.
For ML530 servers position the screws in the right-hand holes on the tape drive (holes 1 and
3), as shown in Figure 5a. For ML570 servers position the screws in the left-hand holes on the
tape drive (holes 2 and 4), as shown in Figure 5b.
Ensure you do use the M3 screws provided - the rails may be attached to the filler panel by
screws of a different thread/size type and these should not be used. If in doubt, refer to your
HP ProLiant server documentation.
Mounting screws
Other HP ProLiant server models, such as ML350 and ML370, only require the use of special
locating screws with no mounting rail.
1
Use a T8 Torx screwdriver to attach the appropriate screws. You may need to purchase the
M3 screws separately. Position the screws in the right-hand holes on the tape drive (holes 1
and 3), as shown in Figure 5c.
•
HP ProLiant ML350: Use M3 mounting screws. These have a thicker head than the standard
M3 screws.
•
HP ProLiant ML370: Use M3 offset mounting screws. These have a thick offset piece and a
thicker head than the standard M3 screws.
Other servers
1
Attach the appropriate mounting hardware. Refer to the manufacturer’s documentation for
instructions.