HP A7518B HP StorageWorks SDLT Tape Drive Getting Started Guide - internal mod - Page 40

Troubleshooting - drivers

Get HP A7518B - StorageWorks SDLT 600 Tape Drive PDF manuals and user guides
UPC - 882780125599
View all HP A7518B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Troubleshooting The first step in problem-solving is establishing whether the problem lies with the cartridge, the drive, the host server and its connections, or with the way the system is being operated. Most modern SCSI host bus adapters locate and display attached devices when the system is booting up. On Windows systems, if you swap or connect a product when your system is running, you will need to reboot the system. IA32 systems also usually need to be rebooted. UNIX systems may have pluggable drivers, which allow drives to be attached to a running system and detected without rebooting. If the device is not detected on boot up, there is probably a problem with the physical hardware: cables, termination, connections, power or the host bus adapter itself. If the device is displayed during boot up but cannot be found in the operating system, this is more likely to be a software problem. • If you encounter a problem during installation and need further clarification, refer to the "Problems encountered during installation" on page 37. • If a problem arises during testing after you have installed the drive, refer to the symptom- based section "Testing after installation" on page 39. • For more information about LED sequences, refer to "Understanding the LEDs" on page 41. • For information about cartridges, refer to "Problems with cartridges" on page 43. Users of most operating systems can use HP Library & Tape Tools to help them diagnose problems. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
36
Troubleshooting
The first step in problem-solving is establishing whether the problem lies with the cartridge, the
drive, the host server and its connections, or with the way the system is being operated.
Most modern SCSI host bus adapters locate and display attached devices when the system is
booting up. On Windows systems, if you swap or connect a product when your system is
running, you will need to reboot the system. IA32 systems also usually need to be rebooted.
UNIX systems may have pluggable drivers, which allow drives to be attached to a running
system and detected without rebooting.
If the device is not detected on boot up, there is probably a problem with the physical
hardware: cables, termination, connections, power or the host bus adapter itself. If the device
is displayed during boot up but cannot be found in the operating system, this is more likely to
be a software problem.
•
If you encounter a problem during installation and need further clarification, refer to the
“Problems encountered during installation” on page 37.
•
If a problem arises during testing after you have installed the drive, refer to the symptom-
based section “Testing after installation” on page 39.
•
For more information about LED sequences, refer to “Understanding the LEDs” on page 41.
•
For information about cartridges, refer to “Problems with cartridges” on page 43.
Users of most operating systems can use HP Library & Tape Tools to help them diagnose
problems.