HP Carrier-grade cc2300 Intel Server Management (ISM) Installation and User&am - Page 14

Step 4. Install ISM

Get HP Carrier-grade cc2300 PDF manuals and user guides View all HP Carrier-grade cc2300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Intel Server Management (ISM) Installation and User's Guide Intel Server Management (ISM) Concepts To avoid an installation failure, you can do any of the following: • Install ISM locally instead of remotely • Disable the Simple File Sharing capability on the remote system • Make sure the remote system is part of a DOMAIN For Windows 2000/Windows 2003 systems, install SNMP as follows: 1. Open the Control panel and select the Add/Remove Programs applet. 2. Click on the Add/Remove Windows Components icon. 3. Click the Management and Monitoring Tools checkbox and then the Next button. 4. On the managed servers, specify these items when configuring SNMP: a. Community string names for SNMP Get and Set operations. b. Community string names for sending traps. c. The trap destination (IP address or name) of the management station that will run the ISM console, as the recipient of the traps. 5. Install and configure any third-party management software package you will use (this item is optional). Step 4. Install ISM ISM is delivered on HP Server cc3310 Information Diagnostics and Utilities Resource CD. The ISM package contains both management station and managed server instrumentation software. The default installation always attempts to install both management station and managed server parts of the software, if it detects that the system is a valid server (it contains a baseboard management controller chip, or BMC, for example). If the system is not determined to be a server, only the management station parts of the software are installed. When installing from a Windows-based system, you can specify automatic remote installation over the network to other systems that run supported Windows or operating systems (see page 9). For Linux servers, you must individually install ISM on each system. Choose the installation instructions below according to the operating systems you use. Each remote server on which you plan to install the ISM package must first be configured locally through the Server Configuration Wizard as described on page 12. Installation for Windows Consoles and Managed Windows Servers Before starting, verify that HP OpenView is not running. Use the instructions below to install to Windows servers. 1. On the management station, run the ISM file SETUP.EXE, either from the ISM CD or as downloaded and unzipped from the web. On the CD, the Setup file is located in the \ISM\Software directory. To automatically run the Setup file from the CD: a. Insert the CD in the drive and it automatically runs, opening a browser window. If auto-load is not enabled, open the CDROM drive and click on welcome.htm. b. Click on ManagementSW tab. c. Click on the Install Ism Server Management button under the Windows install section at the bottom of the page. d. The ISM installation package runs automatically. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Intel Server Management (ISM) Installation and User's Guide
Intel Server Management (ISM) Concepts
14
To avoid an installation failure, you can do any of the following:
•
Install ISM locally instead of remotely
•
Disable the Simple File Sharing capability on the remote system
•
Make sure the remote system is part of a DOMAIN
For Windows 2000/Windows 2003 systems, install SNMP as follows:
1.
Open the Control panel and select the
Add/Remove Programs
applet.
2.
Click on the Add/Remove Windows Components icon.
3.
Click the Management and Monitoring Tools checkbox and then the Next button.
4.
On the managed servers, specify these items when configuring SNMP:
a.
Community string names for SNMP Get and Set operations.
b.
Community string names for sending traps.
c.
The trap destination (IP address or name) of the management station that will run the ISM console,
as the recipient of the traps.
5.
Install and configure any third-party management software package you will use (this item is optional).
Step 4. Install ISM
ISM is delivered on HP Server cc3310 Information Diagnostics and Utilities Resource CD. The ISM package
contains both management station and managed server instrumentation software. The default installation
always attempts to install both management station and managed server parts of the software, if it detects
that the system is a valid server (it contains a baseboard management controller chip, or BMC, for example).
If the system is not determined to be a server, only the management station parts of the software are
installed. When installing from a Windows-based system, you can specify automatic remote installation over
the network to other systems that run supported Windows or operating systems (see page 9). For Linux
servers, you must individually install ISM on each system. Choose the installation instructions below
according to the operating systems you use.
Each remote server on which you plan to install the ISM package must first be configured locally through
the Server Configuration Wizard as described on page 12.
Installation for Windows Consoles and Managed Windows Servers
Before starting, verify that HP OpenView is not running.
Use the instructions below to install to Windows servers.
1.
On the management station, run the ISM file SETUP.EXE, either from the ISM CD or as downloaded
and unzipped from the web.
On the CD, the Setup file is located in the \ISM\Software directory.
To
automatically run the Setup file from the CD:
a.
Insert the CD in the drive and it automatically runs, opening a browser window. If auto-load is not
enabled, open the CDROM drive and click on welcome.htm.
b.
Click on ManagementSW tab.
c.
Click on the Install Ism Server Management button under the Windows install section at the bottom
of the page.
d.
The ISM installation package runs automatically.