HP Cluster Platform Hardware Kits v2010 ProCurve 1U Rack Mount Bracket Install
HP Cluster Platform Hardware Kits v2010 Manual
View all HP Cluster Platform Hardware Kits v2010 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Cluster Platform Hardware Kits v2010 manual content summary:
- HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 1
HP Cluster Platform ProCurve 1U Rack Mount Bracket Installation Guide HP Part Number: 5991-7451 Published: November 2006 - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 2
contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 3
1 Preparing for Installation 1.1 Audience This guide is intended for HP service representatives and other persons trained to install Resources You can download the documentation for components referenced in this installation guide from the following locations: • HP 10000 Series Rack, (Documentation - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 4
• The fasteners specified in Table 1-1. Table 1-1 Fasteners Quantity Size Format Torque 8 M4 x 8 mm Phillips 15 in-lb (Posidrive) 8 10-32 x 0.625 Pan Head XRCS 30 in-lb 4 10-32 Cage Square Nut N/A Nut 4 #10 Alignment N/A Washer Description Rack mount bracket mounting screw (flat- - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 5
- Cage-nut insertion tool (shipped with the rack). - Marker pen or masking tape. - Short stepladder or platform that enables you to install brackets in the upper part of the rack. • Resources: Cables of the type used by the ProCurve switch being installed. Note: Although the ProCurve switch is not a - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 6
Figure 1-3 Slide Brackets 1 2 The following list corresponds to the callouts shown in Figure 1-3: 1. Flat surface of a slide bracket that mounts to the ProCurve switch chassis 2. Thumb screw (two for each slide bracket) that secures the ProCurve switch to the rack mount brackets 1.8 Installation - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 7
2 Installing and Using the ProCurve 1U Rack Mount Brackets 2.1 Identifying the Installation Location The installation location is dependent on the configuration rules for your XC Cluster upgrade bundle. See Section 1.2 for information on where you can obtain XC documentation resources. An upgrade - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 8
Note: To make assembly easier, insert the first screw through the slide bracket hole and hold it in place with the screwdriver tip before you place the slide bracket against the side of the switch. 3. Repeat steps 1 and 2 for the opposite slide bracket. 2.3 Installing the Rack Mount Brackets This - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 9
Figure 2-3 Alignment Washer The raised bumps on the alignment washers (Figure 2-3) face inward, toward the rack mount bracket's threaded insert. 3. Ensure that the rack mount bracket's rear flange is aligned with the correct location on the rack's front column as indicated by callout 3 in Figure - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 10
1. Lift and align the switch so that the slide brackets are level with the rack mount brackets (see callout 1 in Figure 2-4. 2. Slide the switch in until the thumb screws (quantity four) on the slide bracket align with the thread holes in the rack mount bracket (see callout 1 in Figure 2-5). Figure - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 11
3 Cabling and Power Follow the installation instructions for the XC cluster upgrade bundle with which this kit was shipped. See Section 1.2 (page 3) for information the correct sequence. For applications other than the XC series, see the cabling and power-on instructions shipped with your server. 11 - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 12
12 - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 13
connection pathway. 5. Slide the switch all the way out of the rack. 6. Remove the slide brackets from the switch chassis, if necessary, for servicing the ProCurve switch. Important: Carefully retain the slide bracket mounting screws for reuse if the ProCurve switch is to be remounted or if it is - HP Cluster Platform Hardware Kits v2010 | ProCurve 1U Rack Mount Bracket Install - Page 14
*5991-7451* Printed in the US
HP Cluster Platform
ProCurve 1U Rack Mount Bracket
Installation Guide
HP Part Number: 5991-7451
Published: November 2006