HP Digital Sender 9000 HP 9250C Digital Sender - User Guide - Page 29

Initial Setup menu, Networking and I/O

Get HP Digital Sender 9000 PDF manuals and user guides View all HP Digital Sender 9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Initial Setup menu The Initial Setup menu contains the sub-menus shown: ● Networking and I/O menu ● E-mail Setup menu ● Send Setup menu NOTE: Values shown with "(default)" are the factory-default values. Some menu items have no default. Networking and I/O Menu item I/O Timeout Embedded Jetdirect EIO Jetdirect Sub-menu item Values Description Select a value in the range. The factory default setting is 15 seconds. I/O timeout refers to the elapsed time before a job fails. If the stream of data that the device receives for a job gets interrupted, this setting indicates how long the device will wait before it reports that the job has failed. See Table 2-3 Jetdirect sub-menus on page 21 for the list of options. Table 2-3 Jetdirect sub-menus Menu item Sub-menu item TCP/IP Enable Host Name IPV4 Settings Sub-menu item Config Method Values and Description Off: Disable the TCP/IP protocol. On (default): Enable the TCP/IP protocol. An alphanumeric string, up to 32 characters, used to identify the device. This name is listed on the HP Jetdirect configuration page. The default host name is NPIxxxxxx, where xxxxxx is the last six digits of the LAN hardware (MAC) address. Specifies the method that TCP/IPv4 parameters will be configured on the HP Jetdirect print server. Bootp: Use BootP (Bootstrap Protocol) for automatic configuration from a BootP server. DHCP: Use DHCP (Dynamic Host Configuration Protocol) for automatic configuration from a DHCPv4 server. If selected and a DHCP lease exists, DHCP Release and DHCP Renew menus are available to set DHCP lease options. Auto IP: Use automatic link-local IPv4 addressing. An address in the form 169.254.x.x is assigned automatically. Manual: Use the Manual Settings menu to configure TCP/IPv4 parameters, such as an IPv4 address like 123.123.123.123. ENWW Initial Setup menu 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Initial Setup menu
The
Initial Setup
menu contains the sub-menus shown:
●
Networking and I/O
menu
●
E-mail Setup
menu
●
Send Setup
menu
NOTE:
Values shown with "(default)" are the factory-default values. Some menu items have
no default.
Networking and I/O
Menu item
Sub-menu item
Values
Description
I/O Timeout
Select a value in the
range. The factory default
setting is 15 seconds.
I/O timeout refers to the elapsed time before a job fails.
If the stream of data that the device receives for a job
gets interrupted, this setting indicates how long the
device will wait before it reports that the job has
failed.
Embedded Jetdirect
See
Table
2
-
3
Jetdirect sub-menus
on page
21
for the list of options.
EIO <X> Jetdirect
Table 2-3
Jetdirect sub-menus
Menu item
Sub-menu item
Sub-menu item
Values and Description
TCP/IP
Enable
Off
: Disable the TCP/IP protocol.
On
(default): Enable the TCP/IP protocol.
Host Name
An alphanumeric string, up to 32 characters, used to
identify the device. This name is listed on the
HP Jetdirect configuration page. The default host name
is NPIxxxxxx, where xxxxxx is the last six digits of the
LAN hardware (MAC) address.
IPV4 Settings
Config Method
Specifies the method that TCP/IPv4 parameters will be
configured on the HP Jetdirect print server.
Bootp
: Use BootP (Bootstrap Protocol) for automatic
configuration from a BootP server.
DHCP
: Use DHCP (Dynamic Host Configuration
Protocol) for automatic configuration from a DHCPv4
server. If selected and a DHCP lease exists,
DHCP
Release
and
DHCP Renew
menus are available to set
DHCP lease options.
Auto IP
: Use automatic link-local IPv4 addressing. An
address in the form 169.254.x.x is assigned
automatically.
Manual
: Use the
Manual Settings
menu to configure
TCP/IPv4 parameters, such as an IPv4 address like
123.123.123.123.
ENWW
Initial Setup menu
21