HP ENVY 15-q300 ENVY Notebook Maintenance and Service Guide - Page 37

Hard drive, and then disconnect the hard drive connector cable

Get HP ENVY 15-q300 PDF manuals and user guides View all HP ENVY 15-q300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Hard drive NOTE: The hard drive spare part kit does not include the hard drive bracket or hard drive connector cable. The hard drive bracket and hard drive connector cable are included in the Hard Drive Hardware Kit, spare part number 720545-001. Description 2.0-TB, 5400-rpm, 9.5-mm 1.0-TB, 5400-rpm, 9.5-mm 1.0-TB, 5400-rpm, SATA, 7.0-mm, hybrid 8-GB 750-GB, 5400-rpm, 9.5-mm Spare part number 801808-001 778192-001 731999-001 778190-001 Before removing the hard drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 26). 5. Remove the service cover (see WLAN module on page 27). Remove the hard drive: 1. Release the zero insertion force (ZIF) connector (1) to which the hard drive connector cable is attached, and then disconnect the hard drive connector cable (2) from the system board. 2. Release the hard drive connector cable from the tab (3) in the base enclosure. 3. Lift up on the hard drive tab (4) to remove the hard drive from the hard drive bay. 4. If it is necessary to disassemble the hard drive, perform the following steps: Component replacement procedures 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Hard drive
NOTE:
The hard drive spare part kit does not include the hard drive bracket or hard drive connector cable.
The hard drive bracket and hard drive connector cable are included in the Hard Drive Hardware Kit, spare part
number 720545-001.
Description
Spare part number
2.0-TB, 5400-rpm, 9.5-mm
801808-001
1.0-TB, 5400-rpm, 9.5-mm
778192-001
1.0-TB, 5400-rpm, SATA, 7.0-mm, hybrid 8-GB
731999-001
750-GB, 5400-rpm, 9.5-mm
778190-001
Before removing the hard drive, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
26
).
5.
Remove the service cover (see
WLAN module
on page
27
).
Remove the hard drive:
1.
Release the zero insertion force (ZIF) connector
(1)
to which the hard drive connector cable is attached,
and then disconnect the hard drive connector cable
(2)
from the system board.
2.
Release the hard drive connector cable from the tab
(3)
in the base enclosure.
3.
Lift up on the hard drive tab
(4)
to remove the hard drive from the hard drive bay.
4.
If it is necessary to disassemble the hard drive, perform the following steps:
Component replacement procedures
29