HP ENVY 15-q300 ENVY Notebook Maintenance and Service Guide - Page 43

Base enclosure, and any additional screw covers.

Get HP ENVY 15-q300 PDF manuals and user guides View all HP ENVY 15-q300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Base enclosure Description Base enclosure Spare part number 774152-001 Before removing the base enclosure, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 26). 5. Remove the solid-state drive (see WLAN module on page 27). 6. Remove the hard drive (see Hard drive on page 29). Remove the base enclosure: 1. Remove the front rubber feet (1) and any additional screw covers. The front rubber feet and the screw cover are included in the Rubber Kit, spare part number 720559-001. 2. Remove the two Phillips PM2.5×3.5 screws (2) and the six Phillips PM2.5×5.5 screws (3) that secure the base enclosure to the computer. Component replacement procedures 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Base enclosure
Description
Spare part number
Base enclosure
774152-001
Before removing the base enclosure, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
26
).
5.
Remove the solid-state drive (see
WLAN module
on page
27
).
6.
Remove the hard drive (see
Hard drive
on page
29
).
Remove the base enclosure:
1.
Remove the front rubber feet
(1)
and any additional screw covers.
The front rubber feet and the screw cover are included in the Rubber Kit, spare part number
720559-001.
2.
Remove the two Phillips PM2.5×3.5 screws
(2)
and the six Phillips PM2.5×5.5 screws
(3)
that secure the
base enclosure to the computer.
Component replacement procedures
35