HP ENVY TouchSmart 15-q100 ENVY m6 Notebook PC ENVY Notebook PC Maintenance an - Page 73

Power connector cable

Get HP ENVY TouchSmart 15-q100 PDF manuals and user guides View all HP ENVY TouchSmart 15-q100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

5. Remove the three Phillips PM2.0×2.9 screws (1) that secure the connector board to the top cover. 6. Lift the right side of the connector board (2) until it rests at an angle. 7. Remove the connector board (3) by sliding it up and to the right at an angle. Reverse this procedure to install the connector board. Power connector cable Description Power connector cable for use in models with UMA graphics Power connector cable for use in models with discrete graphics Spare part number 720537-001 720538-001 Before removing the power connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 34), and then remove the following components: a. Service cover (see WLAN module on page 35) b. Hard drive (see Hard drive on page 38) c. Base enclosure (see Base enclosure on page 45) Remove the power connector cable: 1. Disconnect the power cable (1) from the system board. 2. Release the power connector cable from the clips (2) built into the keyboard shield. Component replacement procedures 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
5.
Remove the three Phillips PM2.0×2.9 screws
(1)
that secure the connector board to the top cover.
6.
Lift the right side of the connector board
(2)
until it rests at an angle.
7.
Remove the connector board
(3)
by sliding it up and to the right at an angle.
Reverse this procedure to install the connector board.
Power connector cable
Description
Spare part number
Power connector cable for use in models with UMA graphics
720537-001
Power connector cable for use in models with discrete graphics
720538-001
Before removing the power connector cable, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
34
), and then remove the following components:
a.
Service cover (see
WLAN module
on page
35
)
b.
Hard drive (see
Hard drive
on page
38
)
c.
Base enclosure (see
Base enclosure
on page
45
)
Remove the power connector cable:
1.
Disconnect the power cable
(1)
from the system board.
2.
Release the power connector cable from the clips
(2)
built into the keyboard shield.
Component replacement procedures
65