HP Engage Flex Pro G2 Maintenance and Service Guide - Page 90

POST numeric codes and text messages, Table 6-1

Get HP Engage Flex Pro G2 PDF manuals and user guides View all HP Engage Flex Pro G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Table 6-1 POST numeric codes and text messages (continued) Control panel message Description Recommended action 2E5-ECC Memory Module Detected on Unsupported Platform Recently added memory modules support ECC memory error correction. 1. If additional memory was recently added, remove it to see if the problem remains. 2. Check product documentation for memory support information. 2E6-Memory Not Configured Correctly for Proper MEBx Execution DIMM1 is not installed. Be sure that a memory module is in the DIMM1 socket and that it is properly seated. 300-Configuration Change Warning A change in storage configuration has been detected (see the Boot Options menu in BIOS Setup to enable this feature). Either the installed hardware has changed, storage or firmware mode might have been changed, or a storage device might have failed to respond. If no changes were made before this warning, check that the drives are connected properly to power cables and system board. User Diagnostics (f2 during boot-up) might help identify any problem with specific devices. 301-Hard Disk 1: SMART Hard Drive Detects Imminent Failure Hard drive will soon fail. (Some hard 1. drives have a hard drive firmware patch that will fix an erroneous error message.) Determine whether hard drive is giving correct error message. Run the Drive Protection System test under using F2 Diagnostics when booting the computer. 2. Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.) 3. Back up contents and replace hard drive. 302-Hard Disk 2: SMART Hard Drive Detects Imminent Failure Hard drive will soon fail. (Some hard 1. drives have a hard drive firmware patch that will fix an erroneous error message.) Determine whether hard drive is giving correct error message. Run the Drive Protection System test under using F2 Diagnostics when booting the computer. 2. Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.) 3. Back up contents and replace hard drive. 309 - 30C: Hard Disk 3-6: SMART Hard Drive Detects Imminent Failure Hard drive will soon fail. (Some hard 1. drives have a hard drive firmware patch that will fix an erroneous error message.) Determine whether hard drive is giving correct error message. Run the Drive Protection System test under using F2 Diagnostics when booting the computer. 2. Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.) 3. Back up contents and replace hard drive. 3F0-Boot Device Not Found Boot device not found. Insert boot device or load operating system. POST numeric codes and text messages 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
Table 6-1
POST numeric codes and text messages
(continued)
Control panel message
Description
Recommended action
2E5-ECC Memory Module Detected on
Unsupported Platform
Recently added memory modules
support ECC memory error correction.
1.
If additional memory was recently
added, remove it to see if the
problem remains.
2.
Check product documentation for
memory support information.
2E6–Memory Not Configured Correctly
for Proper MEBx Execution
DIMM1 is not installed.
Be sure that a memory module is in
the DIMM1 socket and that it is properly
seated.
300–Configuration Change Warning
A change in storage configuration has
been detected (see the
Boot Options
menu in BIOS Setup to enable this
feature). Either the installed hardware
has changed, storage or firmware mode
might have been changed, or a storage
device might have failed to respond.
If no changes were made before this
warning, check that the drives are
connected properly to power cables
and system board. User Diagnostics (
f2
during boot-up) might help identify any
problem with specific devices.
301-Hard Disk 1: SMART Hard Drive
Detects Imminent Failure
Hard drive will soon fail. (Some hard
drives have a hard drive firmware patch
that will fix an erroneous error message.)
1.
Determine whether hard drive is
giving correct error message. Run
the Drive Protection System test
under using F2 Diagnostics when
booting the computer.
2.
Apply hard drive firmware
patch if applicable. (Available at
http:/
/
www.hp.com/
support
.)
3.
Back up contents and replace hard
drive.
302-Hard Disk 2: SMART Hard Drive
Detects Imminent Failure
Hard drive will soon fail. (Some hard
drives have a hard drive firmware patch
that will fix an erroneous error message.)
1.
Determine whether hard drive is
giving correct error message. Run
the Drive Protection System test
under using F2 Diagnostics when
booting the computer.
2.
Apply hard drive firmware
patch if applicable. (Available at
http:/
/
www.hp.com/
support
.)
3.
Back up contents and replace hard
drive.
309 – 30C: Hard Disk 3–6: SMART Hard
Drive Detects Imminent Failure
Hard drive will soon fail. (Some hard
drives have a hard drive firmware patch
that will fix an erroneous error message.)
1.
Determine whether hard drive is
giving correct error message. Run
the Drive Protection System test
under using F2 Diagnostics when
booting the computer.
2.
Apply hard drive firmware
patch if applicable. (Available at
http:/
/
www.hp.com/
support
.)
3.
Back up contents and replace hard
drive.
3F0–Boot Device Not Found
Boot device not found.
Insert boot device or load operating
system.
POST numeric codes and text messages
83