HP Fortis x360 11 inch G5 Chromebook Maintenance and Service Guide Fortis x360 - Page 38

WLAN module, Remove the Phillips M2.0 × 3.0 screw

Get HP Fortis x360 11 inch G5 Chromebook PDF manuals and user guides View all HP Fortis x360 11 inch G5 Chromebook manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

8. When installing the touchpad and bracket, be sure that the rubber bumper is installed on the bottom of the touchpad bracket in the location shown in the following illustration. To install the touchpad, reverse this procedure. WLAN module To remove the WLAN module, use this procedure and illustration. Table 5-4 WLAN module description and part number Description Intel AX211 Wi-Fi 6E Bluetooth 5.3 WLAN MediaTek MT7921 Wi-Fi 6 + Bluetooth 5.3 WLAN module bracket (available in the Bracket Kit) Spare part number N85418-001 N85419-001 N85029-001 IMPORTANT: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore device functionality, and then contact technical support. Before removing the WLAN module, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 28). 2. Remove the bottom cover (see Bottom cover on page 28). 3. Disconnect the battery cable from the system board (see Battery on page 29). Remove the WLAN module: 1. Remove the Phillips M2.0 × 3.0 screw (1) that secures from the bracket on the WLAN module, and then remove the bracket (2). 2. Disconnect the antenna cables (3) from the module terminals. 3. Remove the module (4) by pulling the it away from the slot at an angle. NOTE: WLAN modules are notched to prevent incorrect installation. WLAN module 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
8.
When installing the touchpad and bracket, be sure that the rubber bumper is installed on the
bottom of the touchpad bracket in the location shown in the following illustration.
To install the touchpad, reverse this procedure.
WLAN module
To remove the WLAN module, use this procedure and illustration.
Table 5-4
WLAN module description and part number
Description
Spare part number
Intel AX211 Wi-Fi 6E Bluetooth 5.3 WLAN
N85418-001
MediaTek MT7921 Wi-Fi 6 + Bluetooth 5.3
N85419-001
WLAN module bracket (available in the Bracket Kit)
N85029-001
IMPORTANT:
To prevent an unresponsive system, replace the wireless module only with a wireless
module authorized for use in the computer by the governmental agency that regulates wireless
devices in your country or region. If you replace the module and then receive a warning message,
remove the module to restore device functionality, and then contact technical support.
Before removing the WLAN module, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
28
).
2.
Remove the bottom cover (see
Bottom cover
on page
28
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
29
).
Remove the WLAN module:
1.
Remove the Phillips M2.0 × 3.0 screw
(1)
that secures from the bracket on the WLAN module, and
then remove the bracket
(2)
.
2.
Disconnect the antenna cables
(3)
from the module terminals.
3.
Remove the module
(4)
by pulling the it away from the slot at an angle.
NOTE:
WLAN modules are notched to prevent incorrect installation.
WLAN module
33