HP G72-257CL Compaq Presario CQ72 Notebook PC and HP G72 Notebook PC - Mainten - Page 51

To remove the hard drive bracket, remove the two Phillips PM3.0×3.5 hard drive bracket screws

Get HP G72-257CL PDF manuals and user guides View all HP G72-257CL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Removal and replacement procedures 3. Remove the three Phillips PM2.5×5.0 screws that secure the hard drive to the computer. 4. Grasp the tab on the hard drive cable connector 1, and lift up to disconnect the cable from the system board. 5. Grasp the Mylar tabs 2 on the hard drive, and then lift the hard drive from the hard drive bay. 6. If you must remove the hard drive cable, disconnect it from the hard drive. 7. To remove the hard drive bracket, remove the two Phillips PM3.0×3.5 hard drive bracket screws 1 from each side of the hard drive. 8. Grasp the 2 attached Mylar tabs and pull the bracket 2 straight up to remove it from the hard drive. Maintenance and Service Guide 4-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Removal and replacement procedures
Maintenance and Service Guide
4–9
3. Remove the three Phillips PM2.5×5.0 screws that secure the hard drive to the computer.
4. Grasp the tab on the hard drive cable connector
1
, and lift up to disconnect the cable from the system board.
5. Grasp the Mylar tabs
2
on the hard drive, and then lift the hard drive from the hard drive bay.
6. If you must remove the hard drive cable, disconnect it from the hard drive.
7. To remove the hard drive bracket, remove the two Phillips PM3.0×3.5 hard drive bracket screws
1
from each
side of the hard drive.
8. Grasp the 2 attached Mylar tabs and pull the bracket
2
straight up to remove it from the hard drive.