Home » HP Manuals » Tower Cases » HP Integrity BLc7000 » Manual Viewer

HP Integrity BLc7000 HP 10GbE Pass-Thru Module User Guide - Page 6

XModem

View all HP Integrity BLc7000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Port mapping For detailed port mapping information, see the HP BladeSystem Enclosure Quick Setup Guide or the HP BladeSystem Enclosure Setup and Installation Guide on the HP website (http://www.hp.com/go/bladesystem/documentation). Dual pass-thru modules In a dual pass-thru module configuration, two pass-thru modules in the HP BladeSystem c7000 Enclosure provide redundant paths to the network ports on the server blades. Redundant paths to server bays In a dual pass-thru module configuration, redundant Ethernet signals from each server blade are routed through the enclosure backplane to separate pass-thru modules within the enclosure. This configuration provides redundant paths to each server bay. Redundant Ethernet signals from each blade server are routed through the enclosure backplane to separate pass-thru modules within the enclosure. However, port to server mapping varies based on the type of server blade installed. XModem The pass-thru module supports XModem for transferring files during firmware upgrade using the serial management port. XModem sends blocks of data and includes an error-detection system called a checksum. When the data is received, the error detection system ensures that the entire message reached its destination. If not, the receiving computer sends a request for data retransmission. Introduction 6

Section	Page
10GbE Pass-Thru Module User Guide	1
Notice	2
Contents	3
Introduction	5
Features	5
Enterprise class performance	5
Configuration and management	5
Diagnostic tools	5
Pass-thru module architecture	5
Port mapping	6
Dual pass-thru modules	6
Redundant paths to server bays	6
XModem	6
Component identification	7
10GbE Pass-Thru Module front panel	7
Installing the pass-thru module	9
Manually configuring the pass-thru module	9
Module security	9
Installing the module	9
Accessing the pass-thru module CLI	10
Accessing the pass-thru module CLI remotely	10
Accessing the pass-thru module CLI locally	11
Production mode CLI	11
CLI menu	11
Installing SFP+ transceivers	12
Replacing a pass-thru module	13
Replacing an existing module	13
Updating the 10GbE pass-thru firmware	14
Methods for updating the 10GbE Pass-Thru Module firmware	14
Updating the firmware image using the Onboard Administrator CLI	14
Updating the firmware image using a USB key and the Onboard Administrator CLI	17
Updating the 10GbE Pass-Thru Module firmware using the pass-thru serial port	18
Performing a serial firmware image download	18
Updating the firmware image using the serial port	18
For more information	20
Additional references	20
Troubleshooting	21
Health LED on the pass-thru module is not on	21
Health LED on the pass-thru module stays amber for more than 30 seconds and pass-thru module does not boot	21
No link LED appears, even after you plug the cable into the SFP+ module	21
Cannot access the pass-thru module serial console interface using an RS232 connection from a PC Terminal Emulation Program	22
Error message appears on the serial console screen that the pass-thru module failed to complete the system self-test	22
The keyboard locks up when you use HyperTerminal to log in to the pass-thru module through the console interface	22
Cannot connect to the pass-thru module console interface remotely using Onboard Administrator	22
The download fails after starting to download the firmware file	23
The pass-thru module configuration is corrupt	23
SFP+ transceiver port is disabled	23
Technical specifications	24
General specifications	24
Port names	24
Physical and environmental specifications	25
Mini-USB to DB-9 serial adapter pin assignment	25
Regulatory compliance notices	27
Class A equipment	27
Modifications	27
Cables	27
Canadian notice	27
European Union regulatory notice	27
Japanese class A notice	28
Korean class A notice	28
Laser compliance	28
Electrostatic discharge	30
Preventing electrostatic discharge	30
Grounding methods to prevent electrostatic discharge	30
Acronyms and abbreviations	31

Match case Limit results 1 per page

Introduction 6

Port mapping

For detailed port mapping information, see the

HP BladeSystem Enclosure Quick Setup Guide

or the

BladeSystem Enclosure Setup and Installation Guide

on the HP website

(

http://www.hp.com/go/bladesystem/documentation

Dual pass-thru modules

In a dual pass-thru module configuration, two pass-thru modules in the HP BladeSystem c7000 Enclosure

provide redundant paths to the network ports on the server blades.

Redundant paths to server bays

In a dual pass-thru module configuration, redundant Ethernet signals from each server blade are routed

through the enclosure backplane to separate pass-thru modules within the enclosure. This configuration

provides redundant paths to each server bay.

Redundant Ethernet signals from each blade server are routed through the enclosure backplane to

separate pass-thru modules within the enclosure. However, port to server mapping varies based on the

type of server blade installed.

XModem

The pass-thru module supports XModem for transferring files during firmware upgrade using the serial

management port. XModem sends blocks of data and includes an error-detection system called a

checksum. When the data is received, the error detection system ensures that the entire message reached

its destination. If not, the receiving computer sends a request for data retransmission.