Home » HP Manuals » Tower Cases » HP Integrity BLc7000 » Manual Viewer

HP Integrity BLc7000 HP 10GbE Pass-Thru Module User Guide - Page 7

Component identification

View all HP Integrity BLc7000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Component identification 10GbE Pass-Thru Module front panel CAUTION: If you press the Reset button while the Health LED is green, the pass-thru module resets. Item 1 2 3 Description UID LED • Blue light on-The pass-thru module is activated. • Blue light off-The pass-thru module is deactivated. Health LED • Off-The pass-thru module is powered off. • Green-The pass-thru module is powered up, and all ports match. • Amber-An issue exists, such as a port mismatch. For more information, see the HP BladeSystem Enclosure Setup and Installation Guide. Ethernet port • Green-Link is 10G. • Flashing green-10G link activity is detected. • Amber-Link is 1G. • Flashing amber-1G link activity is detected. • Flashing alternately green and amber-A link mismatch condition exists. For more information, see the HP BladeSystem Enclosure Setup and Installation Guide. Component identification 7

Section	Page
10GbE Pass-Thru Module User Guide	1
Notice	2
Contents	3
Introduction	5
Features	5
Enterprise class performance	5
Configuration and management	5
Diagnostic tools	5
Pass-thru module architecture	5
Port mapping	6
Dual pass-thru modules	6
Redundant paths to server bays	6
XModem	6
Component identification	7
10GbE Pass-Thru Module front panel	7
Installing the pass-thru module	9
Manually configuring the pass-thru module	9
Module security	9
Installing the module	9
Accessing the pass-thru module CLI	10
Accessing the pass-thru module CLI remotely	10
Accessing the pass-thru module CLI locally	11
Production mode CLI	11
CLI menu	11
Installing SFP+ transceivers	12
Replacing a pass-thru module	13
Replacing an existing module	13
Updating the 10GbE pass-thru firmware	14
Methods for updating the 10GbE Pass-Thru Module firmware	14
Updating the firmware image using the Onboard Administrator CLI	14
Updating the firmware image using a USB key and the Onboard Administrator CLI	17
Updating the 10GbE Pass-Thru Module firmware using the pass-thru serial port	18
Performing a serial firmware image download	18
Updating the firmware image using the serial port	18
For more information	20
Additional references	20
Troubleshooting	21
Health LED on the pass-thru module is not on	21
Health LED on the pass-thru module stays amber for more than 30 seconds and pass-thru module does not boot	21
No link LED appears, even after you plug the cable into the SFP+ module	21
Cannot access the pass-thru module serial console interface using an RS232 connection from a PC Terminal Emulation Program	22
Error message appears on the serial console screen that the pass-thru module failed to complete the system self-test	22
The keyboard locks up when you use HyperTerminal to log in to the pass-thru module through the console interface	22
Cannot connect to the pass-thru module console interface remotely using Onboard Administrator	22
The download fails after starting to download the firmware file	23
The pass-thru module configuration is corrupt	23
SFP+ transceiver port is disabled	23
Technical specifications	24
General specifications	24
Port names	24
Physical and environmental specifications	25
Mini-USB to DB-9 serial adapter pin assignment	25
Regulatory compliance notices	27
Class A equipment	27
Modifications	27
Cables	27
Canadian notice	27
European Union regulatory notice	27
Japanese class A notice	28
Korean class A notice	28
Laser compliance	28
Electrostatic discharge	30
Preventing electrostatic discharge	30
Grounding methods to prevent electrostatic discharge	30
Acronyms and abbreviations	31