HP Integrity rx5670 Hardware Installation Guide - HP Integrity rx5670 (A6837B/ - Page 13

Securing the Cabinet, Unpacking a Non-Racked Server, Unloading with a Lifter,

Get HP Integrity rx5670 PDF manuals and user guides View all HP Integrity rx5670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Server Overview and Unpacking Unpacking the Server WARNING Use caution when rolling the cabinet off the ramp. Make sure the leveling feet on the rack are raised before you roll the rack down the ramp and any time you roll the rack on the casters. A single server in the cabinet weighs approximately 425 pounds. It is strongly recommended that two people roll the cabinet off the pallet. Securing the Cabinet Once in position, secure and stabilize the cabinet using the leveling feet at the corners of the base and install the anti-tip mechanisms on the bottom front and rear of the rack. Figure 1-9 Securing the Cabinet fig016 Unpacking a Non-Racked Server NOTE HP recommends the use of a lifter, such as a RonI Company model 17000 SP 400 lifting device, when moving a non-racked system. Unloading with a Lifter To unload the server from the pallet using a lifter, perform the following steps: WARNING Use caution when using a lifter. An hp Integrity rx5670 may weigh up to 175 pounds. Because of the weight of the server, it must be centered on the lifter forks before raising it off the pallet to avoid injury. Chapter 1 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Chapter 1
Server Overview and Unpacking
Unpacking the Server
13
WARNING
Use caution when rolling the cabinet off the ramp. Make sure the leveling feet on
the rack are raised before you roll the rack down the ramp and any time you roll
the rack on the casters. A single server in the cabinet weighs approximately 425
pounds. It is strongly recommended that two people roll the cabinet off the
pallet.
Securing the Cabinet
Once in position, secure and stabilize the cabinet using the leveling feet at the corners of the base and install
the anti-tip mechanisms on the bottom front and rear of the rack.
Figure 1-9
Securing the Cabinet
Unpacking a Non-Racked Server
NOTE
HP recommends the use of a lifter, such as a RonI Company model 17000 SP 400 lifting device,
when moving a non-racked system.
Unloading with a Lifter
To unload the server from the pallet using a lifter, perform the following steps:
WARNING
Use caution when using a lifter. An hp Integrity rx5670 may weigh up to 175 pounds.
Because of the weight of the server, it must be centered on the lifter forks before
raising it off the pallet to avoid injury.
fig016